Bedienungsanleitung Vermont Castings Radiance Series (Seite 21 von 56) (Englisch)

815507

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

2121 3-90-30007498Vermont Castings • Radiance RADVT Installation Manual_R32 • 10/23

Roof Pitch H(Min.)Ft. Roof Pitch H(Min.)Ft.

Flat to 6/12 1.0* Over 11/12 to 12/12 4.0

Over 6/12 to 7/12 1.25* Over 12/12 to 14/12 5.0

Over 7/12 to 8/12 1.5* Over 14/12 to 16/12 6.0

Over 8/12 to 9/12 2.0* Over 16/12 to 18/12 7.0

Over 9/12 to 10/12 2.5 Over 18/12 to 20/12 7.5

Over 10/12 to 11/12 3.25 Over 20/12 to 21/12 8.0

* 3 Feet. Minimum in Snow Regions

Horizontal

overhang

20 in.

(508 mm)

Lowest

Discharge

Opening

Termination

Cap

Roof Pitch

is X / 12

Vertical

wall

H (min.) - Minimum height

from roof to lowest

discharge opening.

24 in. min.

(610 mm)

Roof Pitch H (Min.) Ft. Roof Pitch H (Min.) Ft.

Flat to 6/12 1.0* Over 11/12 to 12/12 4.0

Over 6/12 to 7/12 1.25* Over 12/12 to 14/12 5.0

Over 7/12 to 8/12 1.5* Over 14/12 to 16/12 6.0

Over 8/12 to 9/12 2.0* Over 16/12 to 18/12 7.0

Over 9/12 to 10/12 2.5 Over 18/12 to 20/12 7.5

Over 10/12 to 11/12 3.25 Over 20/12 to 21/12 8.0

* 3 ft. minimum in snow regions

Storm Collar

Roof

Flashing

Figure 3.18 - Minimum Height from Roof to Lowest Discharge

Opening

Class A Metal Chimney

Prior to installing the gas stove, ensure that the existing

chimney is functionally sound and clean.

• Have the chimney and adjacent structure inspected

and cleaned by qualied professionals. Hearth & Home

Technologies recommends that NFI or CSIA certied

professionals, or technicians under the direction of

certied professionals, conduct a minimum of a NFPA

211 Level 2 inspection of the chimney.

• Replace component parts of the chimney and replace

as specied by the professionals.

1. Remove existing chimney cap.

2. Measure the distance from the top of the chimney to the

bottom of the ceiling support box, add 3 in. (76mm) to

this measurement, and cut a section of 4 in. (101mm)

flex pipe to that length (the flex should be fully extended).

3. Connect the end of the flex pipe section to the underside

of the top adapter, using four sheet metal screws. See

Figure 3.20.

4. Pass the flex pipe down through the center of the

chimney system, and center the top adapter on the top

of the chimney pipe. Drill four 1/8 in. (3mm) diameter

holes through the top adapter, and into the chimney

top. Ensure that you are drilling into the metal on the

chimney. Twist lock the high wind termination cap onto

the top adapter. See Figure 3.21 and Figure 3.22.

Top Adapter

(Included in Link-Stove Kit)

Sheet Metal Screws

4” Flex Pipe

(Included in Link-Stove Kit)

Figure 3.20

Termination Cap

(Includ. in Link-Stove Kit)

Existing Metal

Chimney System

Top Adaptor

(Includ. in Link-Stove Kit)

Direct Vent Pipe

(Length as required)

Flashing

(Includ. in Link-Stove Kit)

4 in. (102mm) Flex Pipe

(Includ. in Link-Stove Kit)

Retro Connector

(Includ. in Link-Stove Kit)

Figure 3.19

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Radiance Series Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vermont Castings Radiance Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info