Bedienungsanleitung Vermont Castings Stardance Series (Seite 10 von 54) (Englisch)

815508

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

1010 3-90-30007467Vermont Castings • Stardance SDDVT Installation Manual_R35 • 11/23

Your stove is approved to be vented either through the side

wall, or vertical through the roof.

• HHT does not require any opening for inspection of vent

pipe.

• Only HHT SLP venting components or DuraVent venting

components specically approved and labeled for this

stove may be used.

• Maintain minimum clearances between vent pipes and

combustible materials.

• Venting terminals shall not be recessed into a wall or

siding.

• Any horizontal run must have a 1/4” rise for every one (1)

foot of run towards the vent termination. Never run the

vent level or down.

There must not be any obstruction such as bushes, garden

sheds, fences, decks or utility buildings within 24" from the

front of the termination hood.

Do not locate termination hood where excessive snow or ice

build up may occur. Be sure to check vent termination area

after snow falls, and clear to prevent accidental blockage of

venting system. When using snow blowers, make sure snow

is not directed towards vent termination area.

Location of Vent Termination

It is imperative the vent termination be located observing the

minimum clearances as shown in this manual.

Vent Termination Clearances

When planning the installation, consider the location of the

vent terminal and clearances. Some of the most common

clearances to keep in mind are shown in Figure 2.11.

Important:All vent clearances must be maintained.

Check your vent termination clearances against Figures

2.11 and 2.12.

The vent should be placed so that people cannot be burned

by accidentally touching the vent surfaces when the stove

is operating.

The vent termination should be located where it cannot be

damaged by such things as automobile doors, lawn mowers

or snowblowers and it should be located away from areas

where it could become blocked by snow, etc.

Some considerations are:

• Obstructions or impediments to venting.

• Nearby combustible materials that could come into

contact with combustion exhaust gases.

• Other nearby openings {within 12" (305 mm)} through

which exhaust gas could reenter the building.

• All vegetation within 3’ (76 mm) that may interfere with

the draft.

Other factors that inuence where the installation will be

sited include the location of outside walls, where additional

heat may be desired in the home, where the family members

gather most regularly, and perhaps most importantly, the

distance limitations of the venting system.

IMPORTANT

The horizontal termination must not be recessed into

the exterior wall or siding.

Horizontal vent runs must be level toward the vent

termination.

Clearances around the vent termination must be

maintained.

For installations using DuraVent pipe, parallel installations

with minimum wall clearance have restricted access for

connecting the Horizontal Vent Cap straps to the vent

pipe. See the maker’s instructions for recommended

installation procedures.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Stardance Series Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vermont Castings Stardance Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info