Bedienungsanleitung Vermont Castings Stardance Series (Seite 19 von 54) (Englisch)

815508

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

1919 3-90-30007467Vermont Castings • Stardance SDDVT Installation Manual_R35 • 11/23

NOTE:Supporthorizontalpipesevery5'(152cm)with

metal pipe straps.

Vent Termination Below Grade:

Install Snorkel Kit #SLP-SNORK when it is not possible to

meet the required vent termination clearances of 12" (305

mm) above grade level. The snorkel kit will allow installation

depth of down to 7" (178 mm) below grade level. The seven

inches is measured from the center of the horizontal vent

pipe as it penetrates the wall. If the venting system is

installedbelowgrade,awindowwellmustbeinstalled

with adequate and proper drainage.

NOTE: Be sure to maintain side wall clearances and vent

run restrictions. Refer to Figures 2.3 thru 2.6.

1. Establish the vent hole through the wall.

2. Remove soil to a depth of approximately 16" (406 mm)

below the base of the snorkel. Install a window well (not

supplied). Rell the hole with 12" (305 mm) of coarse

gravel and maintain a clearance of at least 4" (102 mm)

below the snorkel, Figure 3.16.

3. Install the vent system as described in Figures 3.2 thru

3.9.

4. Be sure to make a watertight joint around the vent pipe

joint at the inside and outside wall joints.

5. Apply high temperature sealant around the inner and

outer snorkel collars. Join the pipes and fasten the

snorkel termination to the wall with the screws provided.

6. Level the soil to maintain a 4" clearance below the

snorkel.

7. If the foundation is recessed, use extension brackets

(not supplied) to fasten the lower portion of the snorkel.

Fasten the brackets to the wall rst, and then fasten to the

snorkel with self-tapping #8 x 1/2" sheet metal screws.

Extend the vent pipes out as far as the protruding wall

face, Figure 3.15.

6. Use appropriate length of pipe sections – telescopic or

xed – and install. The sections which go through the

wall are packaged with the starter kit, and can be cut to

suit if necessary.

7. Guide the vent terminations 4" and 6-5/8” collars into

their respective vent pipes. Double check that the vent

pipes overlap the collars by 2" (51 mm). Secure the

termination to the wall with screws provided and caulk

around the wall plate to weatherproof. As an alternative

to screwing the termination directly to the wall, you

may also use expanding plugs or an approved exterior

construction adhesive.

Figure 3.13 - Horizontal Length Requirement

SLP Cap

Cutout On Vinyl

Vinyl Siding Wall

Termination Cap

Figure 3.14 - Horizontal Termination Cap on a Vinyl Siding Wall

Figure 3.15 - Use extension brackets to mount snorkel against

recessed wall.

ST219

snorkel detail

12/6/99 djt

Recessed Wall

Sheet Metal

Screws and

Bracket

Wall Screws

and Anchors

Waterproof Seal

Around Pipe

Firestop

Finishing

Collar

7" Pipe

Wall Plate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermont Castings Stardance Series Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vermont Castings Stardance Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info