661547
66
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
Battery charger / inverter COMBI-GAMMA
66 090138.02
Use these settings to switch off the Aux-Relay 1 when battery voltage becomes higher •
than a certain limit (E2-05) for a certain time (E2-06)
Note: If E2-06=0 sec (Initial setting), then E2-05 is ignored.*
E2-07: Charging for ? sec
This setting switches the Aux-Relay 1 OFF when the • AC CHARGER started for a certain time
(E2-07). This can be useful when the Aux-Relay 1 is for instance used a low battery alarm.
Use the • Set Udc Lower than ? Voltage (E1-03) setting to start the alarm and use this set-
ting (E2-07) to stop it.
Note: As along as the battery voltage is lower than the specified limit (E1-03), the alarm *
will be active.
E2-08: Fan OFF for ? sec
This will switch the Aux-Relay 1 OFF when the internal fan switches off. This can be used •
together with the E1-08: Fan ON for ? sec setting to drive an external fan.
E2-09: Charge finished for ? Min (When E2-09=0, ignore this setting)
This condition becomes active when the charge bulk phase is finished for a certain time •
(E2-09).
For the charge curve, take a look at for instance the • Charge Current (D1-08) setting.
This is useful when the Aux-Relay 1 is used to start a generator. Once started, one might •
want to keep the generator on until the batteries are more or less charged.
E2-10: Aux-Relay 1 not ON for ? minutes (When E2-10=0, ignore this setting)
If one does not need special off condition, one can use this setting and the Aux-Relay •
1 will switch off automatically when there has been no ON condition for a certain time
(E2-10).
E2-11: AC IN loss for ? sec (When E2-11=0, ignore this setting)
This setting will switch off Aux-Relay1 if the RMS value of • AC IN voltage is too low for a
certain time (E2-11).
This AC level is determined by the • AC IN Low Disconnect (B2-01) setting.
Use this setting (E2-11) to disable re-starting of a generator which is switched off by •
hand when the Aux-Relay 1 is used to generate a start signal for that generator.
E2-12: No Temp. Alarm Select (When E2-13=0, ignore this setting)
E2-13: No Temp. Alarm for ? sec
If you want to switch off the Aux-Relay 1 when there is no over temperature alarm, this •
setting (E2-12) can be used to choose between pre-alarm or normal alarm.
As with other Aux-Relay 1 setting, a delay value must be specified also. This can be •
done with the Delay value for set Aux-Relay 1 OFF when No Overtemperature Alarm
66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Vetus COMBI1524 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Vetus COMBI1524

Vetus COMBI1524 Bedienungsanleitung und Installationsanweisung - Holländisch - 80 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info