Bedienungsanleitung Vibiemme Vibiemme Double Domobar version 3 (Seite 69 von 74) (Englisch)

484572

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

Troubleshooting

1 •

The machine is not working at all and no lights come on.

Be sure it is plugged in and the circuit into which it is plugged is working. Try another outlet if in doubt.

Try an outlet on a circuit that powers no other electrical appliances. Check the voltage of the circuit while the

DD is in operation. Be sure that the PID is on (see Chapter 12) and that the power switch is in “Position I” or

“Position II.”

2 • I hear the pump but no water comes out

Rotary pumps are designed to receive water from a pressurized source. You may need to prime the pump

if you are not using the plumbed option and a situation such as one of the following has taken place:

•

You are using the reservoir for the ﬁrst time

•

You haven’t used the reservoir for a while (such as a plumbed machine being descaled)

•

You ran the reservoir out of water

•

The reservoir pik up hose came out of the water and pulled in air

Follow these directions to prime the pump:

1 Be sure that the water selector valve is switched to the reservoir position (pointing to your LEFT when

looking under the machine from the front)

2 Lift the hose out of the reservoir and remove the ﬁlter from the end of the hose.

3 Hold the hose straight up and using a suitable tool (turkey baster, syringe, or small funnel for example)

completely ﬁll the hose with water.

4 While still holding the ﬁlled hose upwards in one hand, turn the power switch to “Position 1” and lift the

brew lever all the way. Almost immediately, the water in the hose should be drawn into the pump. As soon

as the water level in the hose begins to recede, immediately lower the brew lever fully and turn the

power switch to “Position 0.” If the water is not drawn in you may need to force the water with some pres

sure into the hose while the pump is running. A large size syringe or equivalent tool can be used.

5 Replace the ﬁlter on the end of the hose and lay the ﬁlter ﬂat on the bottom of reservoir.

6 Turn the power switch to “Position I” and lift the brew lever. The pump should now be drawing water from

the reservoir and a ﬂow of water should come from the group.

3 • The brewing temperature is too hot or too cold.

Use the information in Chapter 12 and verify that the PID Offset Temperature has been correctly adjusted

to match the temperature measurement standard you have chosen (the correct offset is 19 for Fahrenheit and

10 for centigrade).

4 •

No water can be pumped when plumbed

Be sure that the valve on the main water source supplying the DD is in the on position (not part of the

DD). Check that the lever on the bottom of the DD is pointing towards the LEFT when facing the front of the

machine.

5 •

I can pump water through the group, but the water is always cold.

Check that the PID is on (Displaying a temperature and not the word “oFF”).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vibiemme Vibiemme Double Domobar version 3 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vibiemme Vibiemme Double Domobar version 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info