Bedienungsanleitung Victron BlueSolar PWM-Light 12 24V-30A (Seite 1 von 1) (Englisch)

785266

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

BlueSolar PWM Light Charge Controller 12/24V

(with light turn-off timer)

Victron Energy bv / De Paal 35 / 1351 JG ALMERE / The Netherlands

Phone: (+31) (0)36 535 97 00 / Fax: (+31) (0)36 535 97 40 / www.victronenergy.com / e-mail: sales@victronenergy.com

Revision : Rev 07

Date : 02-05-2017

1. DESCRIPTION

• Programmable load output with lighting control mode.

• Three stage battery charging (bulk – absorption – float).

• Protected against over current.

• Protected against short circuit.

• Protected against reverse polarity connection of the battery or solar array.

• Low voltage load disconnect.

• Easy to set up thanks to two digit seven segment display.

2. INSTALLATION

The display will show a ‘’12’’ if the Controller detects a 12V battery, and a “24” if

it detects a 24V battery

Do not exceed Solar and Load ratings

3. LED INDICATORS

Green LED:

Off: No sunlight or not enough sunlight. Charger off.

Fast flashing: Bulk charge.

On: Absorption charge.

Slow flashing: Float charge.

LED=Green: battery fully charged (> 12,7V)

LED=Orange: battery ok (12,4V - 12,7V)

LED=Red: battery low (11,2V - 12,4V)

LED=Flashing Red: battery fully discharged (< 11,2V)

(load output cut off level: 11,2V)

LED=ON: load output is on.

LED=OFF: load output is off.

LED=Slow flashing: Overload.

LED=Fast flashing: Short Circuit

Please note:

1. The load output will cut off in case of over load or short circuit. The load output

will attempt to restart after 30 seconds.

2. After over discharge, the load will reconnect automatically when the battery is

recharged to 13,1V / 26,2V.

3. After over discharge, the load can be reconnected manually by pressing the

on/off push button, if the battery voltage exceeds 12,6V / 25,2V.

4. SETTING THE LOAD OUTPUT

4.1 Settings

4.2 Settings description

0 Charger only

The load output is switched off permanently.

1-13 Light control + delay

The load output automatically turns on after sunset (array voltage < 4V) and the

built-in timer starts counting.

When the timer reaches the set time, or when the low voltage limit is reached,

the load output will turn off.

H Manual

The load output can be turned on and off manually with the push button.

(low voltage shutdown remains active)

C Load output controlled by battery voltage only

Load disconnect and load reconnect will be based only on battery voltage, see

section 3

L Dusk to dawn mode

Turn on delay (array voltage < 4V): 10 seconds.

Turn off delay (array voltage > 4V): 1 minute.

No timer function.

d Debug mode

Same as L mode but without delay of 10s/1min

5. SPECIFICATIONS

BlueSolar PWM-Light 12/24-5 12/24-10 12/24-20 12/24-30

Battery Voltage 12/24V with automatic system voltage detection*

Rated charge current 5 A 10 A 20 A 30 A

Recommended solar array

36 cell for 12 V / 72 cell for 24 V

Automatic low voltage load

disconnect Yes

Maximum solar voltage 28 V for a 12 V system and 55 V for a 24 V system (1)

Self-consumption < 10 mA

Overload protection

Shut down after 60 s in case of 130% load

Shut down after 5 s in case of 160% load

Short circuit: immediate shut down

Grounding Common positive

Operating temp. range -20 to +50°C (full load)

Humidity (non condensing) Max 95 %

Settings

Charge voltage 'absorption' 14.2 V / 28,4 V

Charge voltage 'float' 13.8 V / 27,6 V

Load disconnect 11,2V / 22,4V

Load reconnect 12,6V / 25,2V (manual)

13,1V / 26,2V (automatic)

Enclosure

Protection class IP20

Terminal size 5 mm² / AWG10

Weight 0,13 kg 0,15 kg

Dimension (h x w x d) 70 x 133 x 33,5 mm (2.8 x 5.3 x 1.3 inch)

Mounting Vertical wall mount Indoor only

Humidity (non condensing) Max. 95%

Operating temperature -20°C to +50°C (full load)

Cooling Natural convection

Standards

Safety IEC 62109-1

EMC EN 61000-6-1, EN 61000-6-3, ISO 7637-2

1) For 12V use 36 cell solar panels

For 24V use 72 cell solar panels

or 2x 36 cell in series

2) The controller switches to the lower float

voltage level 2 hours after the absorption voltage

has been reached.

Whenever the battery voltage becomes lower

than 13 V, a new charge cycle is triggered.

0 Load output permanently off 9

Load output turned on during 9

hours after sunset

Load output turned on during 1

hour after sunset

Load output turned on during 10

hours after sunset

Load output turned on during 2

hours after sunset

Load output turned on during 11

hours after sunset

Load output turned on during 3

hours after sunset

Load output turned on during 12

hours after sunset

Load output turned on during 4

hours after sunset

Load output turned on during 13

hours after sunset

Load output turned on during 5

hour after sunset

H Manual load control

Load output turned on during 6

hours after sunset

Load output controlled by battery

voltage only

Load output turned on during 7

hours after sunset

L Dusk to dawn mode

Load output turned on during 8

hours after sunset

d Debug mode

IMPORTANT

• Always connect the batteries first, in order to allow the

Controller to recognize system voltage

• Use a 12V (36 cells) solar array for a 12V battery system.

• Use a 24V (72 cells) solar array for a 24V battery system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron BlueSolar PWM-Light 12 24V-30A Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info