785236
12
Zoom out
Zoom in
Vorherige Seite
1/59
Nächste Seite
Rev 5 - 20/01/20
IMT Irradiance Sensor - Victron Installation Guide
Brown: RS485 Data +
Orange: RS485 Data -
Red: Power Pos - 12v to 28v DC
Black: Power Neg/Gnd
Black Thick: Shield
Orange: RS485 Data +
Yellow: RS485 Data -
Brown: Terminator 1 - 120R (not used)
Green: Terminator 2 - 120R (not used)
Red: Power Pos - 5v DC (not used)
Black: Power Neg/Gnd (not used)
DC-DC Converter
Victron Orion 24/12 or 48/12
*See note #1
Terminal Block
*See note #2
Irradiance Sensor
IMT Si-RS485TC Series
*Refer to IMT Irradiance Sensor 'Selection Table for SI Sensor with RS485' RS485 to USB Interface
Victron ASS030572018 / ASS030572050
*See note #3
Battery Bank
PE
INPUT OUTPUT
++
+
Victron GX Device
*Connect to USB port
Installation Notes:
1- The maximum DC power supply voltage permitted for the IMT Irradiance Sensor is 28.0v DC -
accordingly for 24v and 48v battery banks/systems an appropriate DC-DC converter or AC-DC adaptor
must be utilised in the installation.
For 12v battery banks/systems the IMT Irradiance Sensor may be powered directly from the battery
bank and will continue to operate down to minimum voltage of 10.5v (as measured at the sensor).
2- Refer to the IMT Irradiance Sensor 'Quick Reference Guide' for detailed wiring/installation notes and
specifications.
Particularly ensure that;
a) Any extension cabling used complies with the minimum cross-sectional area specifications in
the related table (dependant on DC supply voltage and cable length)
b) Any extension cabling has appropriate shielding and twisted pair cores (recommended)
c) Cabling is installed separated/away from the main DC or AC power cabling
d) All wiring is properly terminated (including unused wires)
e) The sensor housing is not opened or tampered with during installation - as sealing integrity
will be compromised (and warranty void)
3- The IMT Si-RS485TC Series irradiance sensor includes internal Galvanic Isolation (up to 1000v)
between power supply and RS485 modbus circuits, accordingly the non-isolated Victron RS485 to USB
interface is suitable for most installations.
However if an isolated RS485 to USB interface is prefered, the only compatible device is USB485-STIXL
from Hjelmslund Electronics (any others type will not be recognised by the GX device).
+
Installation Notes:
BEWARE! The maximum DC power supply voltage permitted for the IMT Irradiance Sensor is 28.0v DC - accordingly for 24v
and 48v battery banks/systems an appropriate DC-DC converter or AC-DC adaptor MUST be utilised in the installation, eg
a nonisolated 24V to 24V DCDC Converter, or isolated 48V to 24V DCDC Converter, with its input in parallel to the GX Device,
and output connected to Si-Sensor.
For 12v battery banks/systems the IMT Irradiance Sensor may be powered directly from the battery bank and will continue to
operate down to minimum voltage of 10.5v (as measured at the sensor).
Refer to the IMT Irradiance Sensor 'Quick Reference Guide' for detailed wiring/installation notes and specifications. Particularly
ensure that;
Any extension cabling used complies with the minimum cross-sectional area specifications in the related table (dependant on
DC supply voltage and cable length)
Any extension cabling has appropriate shielding and twisted pair cores (recommended)
Cabling is installed separated/away from the main DC or AC power cablingd) All wiring is properly terminated (including un-
used wires)e) The sensor housing is not opened or tampered with during installation - as sealing integrity will be compro-
mised (and warranty void)
Wire connections
Si-Sensor RS 485 interface Signal Note
Black Black Minus Connect to GX Device minus as well.
Brown Orange RS485 Data A +
Orange Yellow RS485 Data B -
Black (thick) Ground Ground
Red Power positive (12/24V) Connect to either battery or output of DCDC Converter
Make sure all unused wires of the RS485 USB interface are terminated in an isolated manner. The data sheet for the RS485 to
USB adapter is here.
Isolated RS485 to USB Adapters
The IMT Si-RS485TC Series irradiance sensor includes internal Galvanic Isolation (up to 1000v) between power supply and
RS485 modbus circuits, accordingly the non-isolated Victron RS485 to USB interface is suitable for most installations. However if
an isolated RS485 to USB interface is preferred (eg positive ground systems), the only compatible device is USB485-STIXL from
Hjelmslund Electronics - Don't use any others, any others type will not be recognised by the GX device.
Configuration of the sensor
Cerbo GX Manual
12
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Victron Cebro GX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info