Bedienungsanleitung Victron Cebro GX (Seite 54 von 59) (Englisch)

785236

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

In more detail, there are several causes for measurement inaccuracies:

1. Part of the power taken from a battery by the inverter is being lost in the inverter, converted into heat: efficiency losses.

2. The Multi does not really measure the power being drawn from the battery. It measures the current at the output of the inver-

ter, and then makes an assumption of the power being drawn from the battery.

3. Watts vs VA: depending on the Multi/Quattro firmware version and also the Cerbo GX firmware version, you are either looking

at VAs (the result of calculating AC voltage * AC current) or looking at a Watts measurement. To see WATTS on the Cerbo

GX, update your Cerbo GX to the latest version (v1.21 or newer). Also make sure the firmware version in your Multi supports

Watts readout, minimum versions are xxxx154, xxxx205 and xxxx300.

4. Multis/Quattros connected to the Cerbo GX via a VE.Bus to VE.Can interface will always reports VAs, not (yet) Watts.

5. If a current sensor assistant is loaded in a Multi/Quattro and no sensor is connected it will return invalid power / kWh values.

6. If a current sensor assistant is loaded in a Multi/Quattro make sure the position is set correctly and the scale match with the

dipswitches on the sensor itself.

7. A current sensor assistant measures and reports VAs, not Watts.

Notes for systems with multiple units in parallel:

1. Cerbo GX version prior to v1.20 use the power and current reported by the master of a phase and multiplied that by the num-

ber of devices in that phase. Since version v1.20 the values of all device is summed per phase and hence should be more

accurate.

2. This revealed a bug for in the firmware of the multi when running in parallel. Ccgx v1.21 workarounds this, by falling back to

the original behavior when it sees an affected firmware version. For better readings the multi's should be updated. The bug

has been fixed in VE.Bus firmware version xxxx159, xxxx209, xxxx306. That firmware was released on February 17th 2015.

3. Multi firmware versions since 26xx207 / xxxx300 can also freeze the Power values at a certain moment in time.

Tips to prevent measurement problems:

1. Do not connect VEConfigure while the Cerbo GX is connected

2. VE.Bus is not a 100% plug and play system: if you disconnect the Cerbo GX from one Multi, and very quickly connect it to

another, it can result it wrong values. To make sure that this is not the case, use the 'redetect system' option in the Multi/

Quattro menu on the Cerbo GX.

13.7. Q7: There is a menu entry named "Multi" instead of the VE.Bus product

name

A VE.Bus system can be completely turned off, including its communication. If you turn a VE.Bus system off, and thereafter reset

the Cerbo GX, the Cerbo GX cannot obtain the detailed product name and shows “Multi” instead.

To get the proper name again, go into the Multi menu on the Cerbo GX and set the Switch menu entry to On or in case a Digital

Multi Control is present, set the physical switch to On. Note that when there is a BMS, above procedure only works when within

battery working voltages.

13.8. Q8: There is a menu entry named "Multi", while there is no Inverter, Multi

or Quattro connected

If a Cerbo GX ever saw a VE.Bus BMS or Digital Multi Control (DMC), it will remember them, until 'Redetect system' is started

from the Cerbo GX menu.After a minute, restart the Cerbo GX: Settings → General → Reboot.

13.9. Q9: When I type the ip-address of the Color Control into my browser, I see

a web page mentioning Hiawatha?

Our plan is to at least run a website where you can change settings and see the current status. If all works out as we would like

to, there might come be a fully functional version of the online VRM Portal running locally on the Cerbo GX. This allows people

without an internet connection, or an intermittent internet connection to have the same features and functionality.

13.10. Q10: I have multiple Solar chargers MPPT 150/70 running in parallel. From

which one will I see the relay status in the Cerbo GX menu?

From a random one.

13.11. Q11: How long should an automatic update take?

The size of the download typically is around 90MB. After download it will install the files which can take up to 5 minutes.

13.12. Q12: I have a VGR with IO Extender, how can I replace this with a Cerbo

GX?

It is not yet possible to replace the IO Extender functionality.

13.13. Q13: Can I use Remote VEConfigure, as I was doing with the VGR2?

Yes, see VE Power Setup manual

Cerbo GX Manual

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron Cebro GX Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info