Bedienungsanleitung Victron EasyPlus 12 1600 70-16 (Seite 10 von 150) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

785549

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

3.3.3 Activating equalisation or forced absorption

The EasyPlus can be put into both these states from the remote panel as well as with the front panel

switch, provided that all switches (front, remote and panel) are set to ‘on’ and no switches are set to

‘charger only’.

In order to put the EasyPlus in this state, the procedure below should be followed.

If the switch is not in the required position after following this procedure, it can be switched over

quickly once. This will not change the charging state.

NOTE: Switching from ‘on’ to ‘charger only’ and vice versa, as described below, must be done quickly. The switch

must be toggled such that the intermediate position is 'skipped', as it were. If the switch remains in the ‘off’

position even for a short time, the device may be turned off. In that case, the procedure must be restarted at step

1. A certain degree of familiarisation is required when using the front switch on the EasyPlus in particular. When

using the remote panel, this is less critical.

Procedure:

1. Check whether all switches (i.e. front switch, remote switch or remote panel switch if present) are

in the ‘on’ position.

2. Activating equalisation or forced absorption is only meaningful if the normal charging cycle is

completed (charger is in 'Float').

3. To activate:

a. Switch rapidly from ‘on’ to ‘charger only’ and leave the switch in this position for ½ to 2 seconds.

b. Switch rapidly back from ‘charger only’ to ‘on’ and leave the switch in this position for ½ to 2

seconds.

c. Switch once more rapidly from ‘on’ to ‘charger only’ and leave the switch in this position.

4. On the EasyPlus the three LEDs ‘Inverter’, ‘Charger’ and ‘Alarm’ will now flash 5 times.

If a MultiControl panel is connected, on the panel the LEDs ‘bulk’, ‘absorption’ and ‘float’ will also

flash 5 times.

5. Subsequently, on the EasyPlus the LEDs ‘Bulk’, ‘Absorption’ and ‘Float’ will each light during 2

seconds.

If a MultiControl panel is connected, on the panel the LEDs ‘bulk’, ‘absorption’ and ‘float’ will also

each light during 2 seconds.

a. If the switch on the EasyPlus is set to ‘on’ while the ‘Bulk’ LED lights, the charger will switch to

equalisation.

Similarly, if the switch on the MultiControl panel is set to ‘on’ while the ‘Bulk’ LED lights, the charger

will switch to equalisation.

b. If the switch on the EasyPlus is set to ‘on’ while the ‘Absorption’ LED lights, the charger will switch

to forced absorption.

Similarly, if the switch on the MultiControl panel is set to ‘on’ while the ‘Absorption’ LED lights, the

charger will switch to forced absorption.

c. If the switch on the EasyPlus is set to ‘on’ after the three LED sequence has finished, the charger

will switch to ‘Float’.

Similarly, if the switch on the MultiControl panel is set to ‘on’ after the three LED sequence has

finished, the charger will switch to ‘float’.

d. If the switch has not been moved, the EasyPlus will remain in ‘charger only’ mode and switch to

‘Float’.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron EasyPlus 12 1600 70-16 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info