Bedienungsanleitung Victron MultiPlus 12 2000 80-32 (Seite 9 von 25) (Englisch)

785523

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

The MultiPlus is provided with a ground relay (relay H, see appendix B) that automatically connects the Neutral output to the

chassis if no external AC supply is available. If an external AC supply is provided, the ground relay H will open before the input

safety relay closes. This ensures the correct operation of an earth leakage circuit breaker that is connected to the output.

• In a fixed installation, uninterruptable grounding can be secured by means of the grounding wire of the AC input. Otherwise the

casing must be grounded.

• In a mobile installation, interrupting the shore connection will simultaneously disconnect the grounding connection. In that case,

the casing must be connected to the chassis (of the vehicle) or to the hull or grounding plate (of the boat).

• In case of a boat, direct connection to the shore ground is not recommended because of potential galvanic corrosion. The

solution to this is using an isolation transformer.

The mains input & output terminal connector can be found on the bottom of the MultiPlus, see appendix A. The shore or mains

cable must be connected to the connector with a three-wire cable. Use a three-wire cable with a flexible core and a cross section

of at least 6 mm². Recommended torque: 1,6 Nm

Procedure (see appendix A) Do not invert neutral and phase when connecting the AC.

The inverter does incorporate a mains frequency isolating transformer. This precludes the possibility of DC current at any AC port.

Therefore type A RCD’s can be used.

•AC-in

The AC input cable can be connected to the terminal block ‘AC–in’.

From right to left: “N” (neutral), “PE” (earth) and “L” (phase)

The AC input must be protected by a fuse or magnetic circuit breaker rated at 32A, and cable cross-section must be

sized accordingly. If the input AC supply is rated at a lower value, the fuse or magnetic circuit breaker should be down sized

accordingly.

•AC-out

The AC output cable can be connected directly to the terminal block ‘AC-out’.

From left to right: “N” (neutral), “PE” (earth) and “L” (phase)

With its PowerAssist feature the MultiPlus can add up to 2kVA (that is 2000 / 230 = 9A) to the output during periods of peak

power requirement. Together with a maximum input current of 32A this means that the output can supply up to 32 + 9 = 41 A.

An earth leakage circuit breaker and a fuse or circuit breaker rated to support the expected load must be included in series with

the output, and cable cross-section must be sized accordingly.

4.4. Optional Connections

A number of optional connections are possible:

Undo the four screws at the front of the enclosure and remove the front panel.

4.4.1. Second Battery

The Multi has a connection (+) for charging a starter battery. For connection see appendix A.

Trickle charge output is protected by automatic overcurrent & overload protection (trip current 1A Imax= 5,5A)

4.4.2. Temperature Sensor

The temperature sensor supplied with the product may be used for temperature-compensated charging. The sensor is insulated

and must be mounted on the battery minus pole. Default output voltages for Float and Absorption are at 25°C. In adjust mode

temperature compensation is disabled.

4.4.3. Remote Control

The product can be remotely controlled in two ways:

• With an external on/off switch (Remove Link “Remote Switch connector H”)

• With a Multi Control Panel

Please see section 5.4 for appropriate DIP switch settings.

4.4.4. Programmable relay

The MultiPlus is equipped with a multi-functional relay that by default is programmed as an alarm relay. The relay can be

programmed for all kinds of other applications however, for example to start a generator (VEConfigure software needed).

4.4.5. Parallel Connection (see appendix C)

The MultiPlus can be connected in parallel with several identical devices. To this end, a connection is established between the

devices by means of standard RJ45 UTP cables. The system (one or more MultiPlus units plus optional control panel) will require

subsequent configuration (see Section 5).

MultiPlus 2kVA 230V

Page 7 Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron MultiPlus 12 2000 80-32 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info