Bedienungsanleitung Victron MultiPlus 12 3000 120-50 (Seite 11 von 164) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch)

785525

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

EN NL FR DE ES SE Appendix

4.3 Connection of the AC cabling

The MultiPlus is a safety class I product (supplied with a ground terminal for

safety purposes). Its AC input and/or output terminals and/or

grounding point on the outside of the product must be provided with

an uninterruptible grounding point for safety purposes.

The MultiPlus is provided with a ground relay (relay H, see appendix B) that

automatically connects the Neutral output to the chassis if no external

AC supply is available. If an external AC supply is provided, the ground

relay H will open before the input safety relay closes. This ensures the

correct operation of an earth leakage circuit breaker that is connected to

the output.

─ In a fixed installation, an uninterruptable grounding can be secured by

means of the grounding wire of the AC input. Otherwise the casing

must be grounded.

─ In a mobile installation (for example, with a shore current plug),

interrupting the shore connection will simultaneously disconnect the

grounding connection. In that case, the casing must be connected to

the chassis (of the vehicle) or to the hull or grounding plate (of the

boat).

In case of a boat, direct connection to the shore ground is not

recommended because of potential galvanic corrosion. The solution to this

is using an isolation transformer.

Torque: 2 Nm max. 2.3 Nm

The terminal blocks can be found on the printed circuit board, see Appendix A.

4.3.1 Models with 16 A transfer capacity (eg MultiPlus 12/3000/120-16 230 V)

• AC-in

The AC input cable must be connected to the terminal block “AC–in”.

From left to right: “PE” (earth), “L” (phase) and “N” (neutral).

The AC input must be protected by a fuse or magnetic circuit breaker rated at 16 A or less, and cable cross-section must

be sized accordingly. If the input AC supply is rated at a lower value, the fuse or magnetic circuit breaker should be down sized

accordingly.

• AC-out-1

The AC output cable can be connected directly to the terminal block "AC-out-1".

From left to right: “L” (phase) “N” (neutral) and “PE” (earth).

With its PowerAssist feature the Multi can add up to 3 kVA (that is 3000 / 230 = 13 A) to the output during periods of peak power

requirement. Together with a maximum input current of 16 A this means that the output can supply up to 16 + 13 = 29 A.

An earth leakage circuit breaker class A and a fuse or circuit breaker rated to support the expected load must be included

in series with the output, and cable cross-section must be sized accordingly. The maximum rating of the fuse or circuit

breaker is 32 A.

• AC-out-2

A second output is available that disconnects its load in the event of battery operation. On these terminals, equipment is connected

that may only operate if AC voltage is available on AC-in, e.g. an electric boiler or an air conditioner. The load on AC-out-2 is

disconnected immediately when the Multi switches to battery operation. After AC power becomes available on AC-in-1 or AC-in-2,

the load on AC-out-2 will be reconnected with a delay of approximately 2 minutes. This to allow a genset to stabilise.

AC-out-2 can support loads of up to 16 A. An earth leakage circuit breaker and fuse rated at max. 16A must be connected in series

with AC-out-2.

Note: Loads connected to AC-out-2 will be taken into account in the PowerControl / PowerAssist current limit setting. Loads

directly connected to the AC supply will not be included in the PowerControl / PowerAssist current limit setting.

4.3.2 Models with 50 A transfer capacity (eg MultiPlus 12/3000/120-50 230 V)

• AC-in

The AC input cable can be connected to the terminal block “AC–in”.

From left to right: “L” (phase) “N” (neutral) and “PE” (earth).

The AC input must be protected by a fuse or magnetic circuit breaker rated at 50 A or less, and cable cross-section must

be sized accordingly. If the input AC supply is rated at a lower value, the fuse or magnetic circuit breaker should be down sized

accordingly.

• AC-out-1

The AC output cable can be connected directly to the terminal block "AC-out".

From left to right: “L” (phase) “N” (neutral) and “PE” (earth).

With its PowerAssist feature the Multi can add up to 3 kVA (that is 3000 / 230 = 13 A) to the output during periods of peak power

requirement. Together with a maximum input current of 50 A this means that the output can supply up to 50 + 13 = 63 A.

An earth leakage circuit breaker class A and a fuse or circuit breaker rated to support the expected load must be included

in series with the output, and cable cross-section must be sized accordingly. The maximum rating of the fuse or circuit

breaker is 63 A.

• AC-out-2

See section 4.3.1.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron MultiPlus 12 3000 120-50 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info