Bedienungsanleitung Victron MultiPlus 24 1200 25-16 (Seite 15 von 146) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

785518

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

EN NL FR DE ES IT Appendix

Ground relay (see appendix B)

With this relay (H), the neutral conductor of the AC output is grounded to the chassis when

the back-feed safety relay is open. This ensures the correct operation of earth leakage

circuit breakers in the output.

If a non-grounded output is required during inverter operation, this function must be turned

off.

(Use VE-Configure)

The standard setting is ‘Four-stage adaptive with BatterySafe mode’. See Section 2 for a

description.

This is the recommended charge curve. See the help files in the software configuration

programs for other features.

Battery type

The standard setting is the most suitable for Victron Gel Deep Discharge, Gel Exide A200,

and tubular plate stationary batteries (OPzS). This setting can also be used for many other

batteries: e.g. Victron AGM Deep Discharge and other AGM batteries, and many types of

flat-plate flooded batteries. Four charging voltages can be set with DIP switches.

Automatic equalisation charging

This setting is intended for tubular plate traction batteries. During absorption the voltage

limit increases to 2,83V/cell (34V for a 24V battery) once the charge current has tapered

down to less than 10% of the set maximum current.

Absorption time

The absortion time depends on the bulk time (adaptive charge curve), so that the battery is

optimally charged. If the ‘fixed’ charging characteristic is selected, the absorption time is

fixed. For most batteries, a maximum absorption time of eight hours is suitable. If an extra

high absorption voltage is selected for rapid charging (only possible for open, flooded

batteries!), four hours is preferable. With DIP switches, a time of eight or four hours can be

set. For the adaptive charge curve, this determines the maximum absorption time.

Storage voltage, Repeated Absorption Time, Absorption Repeat Interval

See Section 2.

Bulk Protection

Default setting: off. When this setting is ‘on’, the bulk charging time is limited to 10 hours. A

longer charging time could indicate a system error (e.g. a battery cell short-circuit).

AC input current limit

These are the current limit settings at which PowerControl come into operation. The factory

setting is 12A.

UPS feature

If this setting is ‘on’ and AC on the input fails, the Multi switches to inverter operation

practically without interruption. The Multi can therefore be used as an Uninterruptible Power

Supply (UPS) for sensitive equipment such as computers or communication systems.

The output voltage of some small generator sets is too unstable and distorted for using this

setting* – the Multi would continually switch to inverter operation. For this reason, the setting

can be turned off. The Multi will then respond less quickly to AC input voltage deviations. The

switchover time to inverter operation is consequently slightly longer, but most equipment

(most computers, clocks or household equipment) is not adversely impacted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron MultiPlus 24 1200 25-16 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info