Bedienungsanleitung Victron MultiPlus 48 1200 13-16 (Seite 12 von 146) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

785519

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

4.4 Optional Connections

A number of optional connections are possible:

Undo the four screws at the front of the enclosure and remove the front panel.

4.4.1 Second Battery

The Multi has a connection (+) for charging a starter battery. For connection see appendix A.

Trickle charge output is protected by automatic overcurrent & overload protection (trip current

1A Imax= 5,5A)

4.4.2 Temperature Sensor

The temperature sensor supplied with the product may be used for temperature-compensated

charging. The sensor is insulated and must be mounted on the battery minus pole. Default

output voltages for Float and Absorption are at 25°C. In adjust mode temperature

compensation is disabled.

4.4.3 Remote Control

The product can be remotely controlled in two ways:

- With an external 3 position switch

- With a Multi Control Panel

Please see section 5.5.1. for appropriate DIP switch settings.

4.4.4. Programmable relay

The Multi is equipped with a multi-functional relay that by default is programmed as an alarm

relay. The relay can be programmed for all kinds of other applications however, for example to

start a generator (VEConfigure software needed).

4.4.5 Parallel Connection (800VA and 1200VA models only, see appendix C)

The MultiPlus can be connected in parallel with several identical devices. To this end, a

connection is established between the devices by means of standard RJ45 UTP cables. The

system (one or more MultiPlus units plus optional control panel) will require subsequent

configuration (see Section 5).

In the event of connecting MultiPlus units in parallel, the following requirements must be met:

- A maximum of six units connected in parallel.

- Only identical devices may be connected in parallel.

- The DC connection cables to the devices must be of equal length and cross-section.

- If a positive and a negative DC distribution point is used, the cross-section of the connection between the

batteries and the DC distribution point must at least equal the sum of the required cross-sections of the

connections between the distribution point and the MultiPlus units.

- Place the MultiPlus units close to each other, but allow at least 10 cm for ventilation purposes under,

above and beside the units.

- UTP cables must be connected with a Splitter from one unit to the other (and to the remote panel).

Connection/splitter permitted.See Appendix C

- A battery-temperature sensor need only be connected to one unit in the system. If the temperature of

several batteries is to be measured, you can also connect the sensors of other MultiPlus units in the system

(with a maximum of one sensor per MultiPlus). Temperature compensation during battery charging

responds to the sensor indicating the highest temperature.

- Only one remote control means (panel or switch) can be connected to the system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron MultiPlus 48 1200 13-16 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info