Bedienungsanleitung Victron Phoenix 12 2000 Omvormer (Seite 7 von 86) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch)

785436

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

EN NL FR DE ES SE Appendix

Red LED On or blinking

The inverter did shut down because of a protection. It will

no longer automatically restart. The red LED indicates the

reason for shutdown. Remove the cause and then restart

the inverter by switching it Off, and then back On.

Red LED

Definition

Trouble shooting

●●●●●●●● Solid on

Overload

Reduce load

●●●●----

Slow

blink

Low batt.

Recharge or replace battery

Check DC cable connections

Check cable cross section as it may be insufficient.

See section 4.2 Protections and automatic restarts for

manual and automatic restart behavior.

●-●-●-●-

Fast

blink

High batt.

Reduce DC input voltage, check for faulty charger

●-●-----

Double

pulse

High temp.

Reduce load and/or move inverter to better ventilated area

●---●---

Fast

single pulse

High DC ripple

Check DC cable connections and cable cross section.

3.4 Protections and automatic restarts

Overload

Some loads like motors or pumps draw large inrush currents in a start-up situation. In

such circumstances, it is possible that the start-up current exceeds the over current trip

level of the inverter. In this case the output voltage will quickly decrease to limit the output

current of the inverter. If the over current trip level is continuously exceeded, the inverter

will shut down: wait 30 seconds and then restart.

After three restarts followed by another overload within 30 seconds of restarting, the inverter

will shutdown and remain off. The LEDs will signal shutdown due to overload. To restart the

inverter, switch it Off, then On.

Low battery voltage (adjustable)

The inverter will shut down when the DC input voltage drops below the low battery shutdown

level. After a minimum delay of 30 seconds, the inverter will restart if the voltages rise above

the low battery restart level.

After three restarts followed by a low battery shutdown within 30 seconds of restarting, the

inverter will shutdown and stop retrying. The LEDs will signal low battery shutdown. To restart

the inverter, switch it Off, and then On, or recharge the battery: as soon as the battery has

risen and then stays above the Charge detect level for 30 seconds, it will switch on.

See the Technical Data table for default low battery shutdown and restart levels. They can be

changed with the VictronConnect App.

High battery voltage

Reduce DC input voltage and/or check for a faulty battery- or solar-charger in the system.

After shutting down due to a high battery voltage, the inverter will first wait 30 seconds and

then retry operation as soon as the battery voltage has dropped to acceptable level. The

inverter will not stay off after multiple retries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron Phoenix 12 2000 Omvormer Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info