Bedienungsanleitung Victron Phoenix acculader 24 16 (Seite 5 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch)

785490

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

victron energy

GB NL F D I DK ΕΛ N P E S Specs

Controls

The Phoenix Charger will start charging by

switching it ON with the switch at the front panel.

One of the LED’s at the front will indicate the

progress of charge state:

Battery is less then 80%

charged.

Battery is approximately

charged for 80%. If Bulk LED

is illuminating as well the set

absorption voltage has not yet

been reached (Battery Safe

Mode).

Battery is fully charged and

will be kept charged with

trickle charge.

An output fuse is defective or

the ambient temperature of

the charger is too high.

The Phoenix Charger will stop charging by

switching it OFF with the switch at the front panel.

Equalize a traction set

This is done at a higher voltage than most DC-

equipment can handle so all consumer electronics

should be disconnected before equalizing the

battery.

• Put the charger in off position. Switch ON-OFF-

ON within 2 seconds.

• You’ll see all the LED’s flashing 5 times. After

the 5th time all LEDs illuminate in sequence:

• Bulk –switch OFF-ON when this LED lights up.

Now the charger increases its voltage up to 1 Volt

above Absorption voltage for a 12V model or 2

Volts for a 24V model. The maximum current in

this mode is limited to ¼ of the adjusted maximum

charge current. The charger will stay in this mode

for 1 hour and then switches to Float mode.

Equalizing will only work with an already charged

battery. If the battery voltage remains too low (see

specs) for > 60 seconds the charger switches to

Bulk mode and continues charging according

normal charging characteristic.

Force to Absorption mode for fixed time

In certain circumstances it can be desirable to

charge the battery occasionally with Absorption

voltage for a fixed time.

• Put the charger in off position. Switch ON-OFF-

ON within 2 seconds.

• You’ll see all the LED’s flashing 5 times. After

the 5th time a sequence starts:

• Bulk –wait.

• Absorption –switch OFF-ON when this LED

lights up.

Now the charger will stay in Absorption mode for

the default or adjusted fixed Absorption time.

Remote control

The Phoenix Charger can be remote controlled

optionally. With the Phoenix Charger Control all

indicators can be seen and additionally the

charging current. With this remote control it is

possible to temporarily limit the charging current.

This could be useful in case of a low current mains

connection in combination with other utility

equipment.

TROUBLESHOOTING

Problem

Possible cause

Solution

Failure LED

illuminates The output fuses are

defect Return the product to your

dealer

The ambient

temperature of the

charger is too high

Put the charger in a cool

and well ventilated

environment

Charger does

not function The mains voltage is

not ok Measure the mains voltage

and make it within specs

The input fuse is

defect Return the product to your

dealer

The battery

doesn’t get fully

charged

A bad battery

connection Check the battery

connections

The Absorption

voltage is wrongly

adjusted

Consult your battery

supplier and electrician and

have the charging voltage

adjusted

The float voltage is

wrongly adjusted

The battery capacity

is too large Make sure the charger

matches the battery

capacity

The output fuses are

defect Return the product to your

dealer

The battery is

being

overcharged

The Absorption

voltage is wrongly

adjusted

Consult your battery

supplier and electrician and

have the charging voltage

adjusted

The float voltage is

wrongly

adjusted

A single battery cell

is defect Replace the battery or the

defect cell

Too small a battery Consult your battery

supplier and electrician and

have the charging current

adjusted

The ambient

temperature of the

battery is too high

Consult your electrician and

let him connect a

temperature sensor

Failure

Float

Absorpt

Bulk

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron Phoenix acculader 24 16 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info