785490
8
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
7
victron energy
Adjustments without remote panel
WARNING: Always check with your battery
supplier if the choosen charge characteristic is
suitable for your battery and application
Remove the frontplate and disconnect battery
and Voltage sense and Temperature sense and
connect a digital voltmeter to – and +1 output.
Bulk-current
While switching on keep both the pushbuttons
&
pushed.
Release pushbuttons.
Bulk LED is flashing alternately with Failure LED.
Push
for up and
for down.
Reading as follows:
Discard first digit of DVM then multiply by 10, i.e:
22.50V => ….2.50 => 25 Amps
15.00V => .....5.00 => 50 Amps
Switch the charger Off to store.
Absorption and Float voltage
While switching on keep the pushbutton
pushed for Absorption voltage and
for Float-
voltage.
Release pushbuttons.
Absorption or Float LED is flashing alternately
with Failure LED.
Push
for up and
for down.
Reading on voltmeter as is.
Switch the charger Off to store.
Please note that in adjust-mode the
Temperature sense compensation is not taken
into account.
Warning: If the charger is not switched Off
after an adjustment the new value will not be
stored but will remain on the outputs. After 4
hours the charger continues the normal
sequence with the old values. This can be
useful if a forced high voltage is wanted to get
some life in an assumed ‘dead’ battery.
Return to factory settings
Switch the charger on.
Keep the pushbutton
and/ or
pushed while
switching off.
The factory settings are restored.
When ready
Connect battery and if applicable Voltage sense
and Temperature sense.
Replace the frontplate.
20AT
20AT
20AT
20AT
PE earth connection
N AC input : Neutral
L AC input : Line
+ battery 1
+ battery 2
- battery
+ Trickle charge
- Trickle charge
+ Voltage sense
- Voltage sense
+ Temperature sense
- Temperature sense
Remote
co
nnector
<= =>
Adjusting maximum Bulk current
20AT
20AT
20AT
20AT
PE earth connection
N AC input : Neutral
L AC input : Line
+ battery 1
+ battery 2
- battery
+ Trickle charge
- Trickle charge
+ Voltage sense
- Voltage sense
+ Temperature sense
- Temperature sense
Remote
co
nnector
<= =>
Adjusting Float voltage
20AT
20AT
20AT
20AT
PE earth connection
N AC input : Neutral
L AC input : Line
+ battery 1
+ battery 2
- battery
+ Trickle charge
- Trickle charge
+ Voltage sense
- Voltage sense
+ Temperature sense
- Temperature sense
Remote
co
nnector
<= =>
Adjusting Absorption voltage
20AT
20AT
20AT
20AT
PE earth connection
N AC input : Neutral
L AC input : Line
+ battery 1
+ battery 2
- battery
+ Trickle charge
- Trickle charge
+ Voltage sense
- Voltage sense
+ Temperature sense
- Temperature sense
Remote
co
nnector
<= =>
Restoring defaults
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Victron Phoenix acculader 24 16 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info