Bedienungsanleitung Victron SmartSolar MPPT 250 60 MC4 (Seite 19 von 145) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch)

785405

Zoom out

Zoom in

Vorherige Seite

1/145

Nächste Seite

EN NL FR DE ES SE Appendix

Using the pluggable LCD display or VictronConnect and the procedures

below, most errors can be quickly identified. If an error cannot be resolved,

please refer to your Victron Energy supplier.

Error nr.

Problem

Cause / Solution

n. a.

The LCD does not light up

(no backlight, no display)

The internal power supply used for powering

the converter and the backlight is derived from

either the solar-array or the battery.

If PV and battery voltage are both below 6V

the LCD will not light up. Make sure that the

LCD display is properly inserted into the

socket.

n. a.

The LCD does not light up

(backlight works, no display,

charger seems to work)

This may be due to low ambient temperature.

If the ambient temperature is below -100C

(140F) the LCD-segments can become vague.

Below -200C (-40F) the LCD-segments can

become invisible.

During charging the LCD-display will warm up,

and the screen will become visible.

n. a.

The charge controller does

not charge the battery

The LCD-display indicates that the charge-

current is 0 Amps.

Check the polarity of the solar-panels.

Check the battery breaker

Check if there is an error indication on the LCD

Check if the charger is set to "ON" in the

menu.

Check if the Remote input is connected.

Check if the right system voltage has been

selected

n. a.

High temperature: the

thermometer icon blinks

This error will auto-reset after temperature has

dropped.

Reduced output current due to high

temperature.

Check the ambient temperature and check for

obstructions near the heatsink.

Err 2

Battery voltage too high

(>76,8V)

This error will auto-reset after the battery

voltage has dropped.

This error can be due to other charging

equipment connected to the battery or a fault

in the charge controller.

Err 17

Controller overheated

despite reduced output

current

This error will auto-reset after charger has

cooled down.

Check the ambient temperature and check for

obstructions near the heatsink.

Err 18

Controller over-current

This error will auto-reset.

Disconnect the charge controller from all

power-sources, wait 3 minutes, and power up

again.

If the error persists the charge controller is

probably faulty.

Err 20

Maximum Bulk-time

exceeded

This error can only occur when the maximun

bulk-time protection is active. This error will not

auto-reset.

This error is generated when the battery-

absorption-voltage is not reached after 10

hours of charging.

For normal solar installations it is advised not

to use the maximum bulk-time protection.

Err 21

Current sensor issue

The charge controller is probably faulty.

This error will not auto-reset.

Err 26

Terminal overheated

Power terminals overheated, check wiring and

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron SmartSolar MPPT 250 60 MC4 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info