Bedienungsanleitung Videologic DRX-601E (Seite 8 von 16) (Englisch)

529136

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Switching on and off

Before switching on for the first time, check all connections and ensure that the volume on your

amplifier is turned down.

We recommend that you switch off your DRX-601E/ES when not in use to prevent energy

wastage. Note that if you leave the unit switched off for an extended period (around a month or

longer) you may need to re-tune the unit to refresh the available services.

Push and release the Power button on the front of your DRX-601E/ES to switch the unit on or

off. The blue power on LED will light up when the unit is switched on.

You should now perform the tuning operation described below.

Using your DRX-601E/ES

This section provides information on using the main functions of your DRX-601E/ES including tuning, selecting a service and altering the

displayed information.

Tuning

Tuning the DRX-601E/ES is very simple. In most cases you only need to perform this

operation once, when you first set up the unit. The tuning facility has two modes:

Rapid - scans frequencies in the UK channel allocation. This should take around 45 seconds.

Full - scans the full range of digital frequencies in Band III. This may take several minutes.

All UK digital radio services currently available in your area will be found using the rapid mode.

1. Ensure your DRX-601E/ES is switched on and your aerial is connected and positioned

correctly.

2. Push and release the Autotune button on the front of your DRX-601E/ES once for rapid

mode and twice for full mode.

Note

You can cancel Autotune by pushing the Autotune button a third time.

The display will indicate tuning is underway. When finished, the name of the first service

found will be shown on the top line of the display and you should hear it through your

speakers. All the services found are now stored in the unit and you can select a service

as described below.

Note

If no services are found the display will show the message NO ENSEMBLES. Check your

aerial connection and positioning and try the tuning process again.

You may want to repeat this procedure in the future if you change your aerial position or if you

want to receive a newly introduced service.

Selecting a service

Once you have tuned your DRX-601E/ES as explained above you can select the digital radio

service you want to listen to. You use the large turn-and-push button to select a service.

1. Rotate the large tuning button to see the names of other stored services on the bottom

line of the display. Stop when you find the service you want to listen to.

2. Push and release the large tuning button to listen to the service you have selected.

If the service you select is in stereo, the Stereo LED will light up. If the service you select has

one or more secondary services available, the Secondary LED will light up.

See page 9 for information on primary and secondary services and see page 8 for details on

selecting primary or secondary services.

Note If reception is poor, check the signal strength and try repositioning your aerial using the

signal strength indicator as described on page 7.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Videologic DRX-601E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info