Bedienungsanleitung Viessmann Vitoligno 300C (Seite 41 von 52) (Englisch)

813613

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

5790 982 - 02

Vitoligno 300-C Operating Scanning

Scanning Information (continued)

Shutting Down the Heating System for an Extended Period

Calling up temperatures in the extended menu

Press the following keys:

1. for “Extended menu”.

2. |/~ for “Information”

3. d to confirm.

4. |/~ for “General”, “Boiler”, “Heating” or “DHW”.

The following overviews show the temperatures

displayed in the sub-menus.

5. d to confirm.

Temperatures in “General” sub-menu:

 Outdoor temperature

 Set system temperature

Temperatures in “Boiler” sub-menu:

 Boiler water temperature

 Boiler return

 Flue gas temperature

Temperatures in “Heating” sub-menu:

 Set room temperature

 Set reduced room temperature

 Set supply temperature

 Actual supply temperature

Temperature in “DHW” sub-menu:

 Set DHW temperature

 Actual DHW temperature

 Set return temperature

 Actual return temperature

Calling up temperatures

You can scan temperatures in the standard menu and

in the extended menu. The range of displayed values

is wider in the extended menu. We therefore recommend

calling up temperatures via the extended menu.

Calling up temperatures in the standard menu

Press the following keys:

1. |/~ for “Information”

2. d to confirm.

3. |/~ for “Outdoor temperature”, “Heating” or “DHW”.

The overview below shows the temperatures displayed in

the “Heating” and “DHW” submenus.

“Heating” sub-menu:

 Set supply temperature

 Actual supply temperature

“DHW” sub-menu:

 Set DHW temperature

 Actual DHW temperature

 Set return temperature

 Actual return temperature

Scanning the heating water buffer tank temperatures

in the standard menu

Press the following keys:

1. |/~ for “Buffer”

2. d to confirm.

3. |/~ to display the required temperature

The following temperatures can be called up in the

“Buffer” menu:

 Set buffer

 Buffer average

 Buffer sensors

You can switch your heating system off if you do not intend

to use it. We recommend you contact your heating contractor

before and after shutting down for longer periods.

Your heating contractor can then take suitable steps,

such as frost protection for the system or heating surface

preservation, as required.

Note: No special measures are required when shutting

down the system on a temporary basis.

1. Switch off the boiler by pressing “START/STOP”

on the control unit.

2. Wait until the run-on time has passed and let the

boiler cool down.

Shutdown

3. Perform all work described in the overview of chapter

“Maintenance” starting on page 44.

4. When there is a risk of frost, drain the boiler,

observing the instructions issued by your heating

system installer or ask them to charge the system

with antifreeze.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Viessmann Vitoligno 300C Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Viessmann Vitoligno 300C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info