Bedienungsanleitung View Quest Retro (Seite 13 von 17) (Englisch)

594799

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

GB GB

Retro DAB+ Operation Guide

Alarm Sounds

- If the alarm is set to DAB/DAB+ mode and no DAB/DAB+ stations can be received, BEEP Tone1

will sound.

- If the alarm is set to “iPod” mode and there is no iPod connected, BEEP Tone1 will sound.

- Whether “iPod” or “BEEPER” alarms are sounding, docking or removing an iPod or iPhone will

turn off the alarm.

- If two alarms are set, when ALARM 1 is sounding and ALARM 2 begins to sound, it will

automatically turn off ALARM 2.

Alarm Volume

Whichever alarm mode is selected, the alarm volume will be half the maximum volume.

Sleep Timer

You can send your Retro DAB+ to sleep for up to 90 minutes time.

In working mode, press and hold SNOOZE (9) to enter sleep function setting. The display will show ‘Sleep

Timer‘ with “OFF” ashing on the lower right. Press (4) or (6) to select sleep time from 15min,

30min, 45min, 60min or 90min. Press (5) to conrm your selection.

Sleep time will be displayed as ‘Snn’ on the upper right of the screen, where ‘nn’ is the sleep time selected.

To cancel the sleep timer, follow instructions above and select ‘off’ instead of a sleep time.

Other Operations

Your Retro DAB+ has two functions that you are only likely to need in the unlikely event of a problem while

in conversation with support.

Factory Reset

[Note] Factory Reset will cancel all your presets

In working mode, press and hold “MODE” button until “Press Enter Key to Reset” is displayed.

Then press (5) to conrm. “System Reset, then System Reset OK” will display.

Software Version

In working mode, press and hold INFO to check the software version.

5. Set alarm time hours by pressing (4) or (6). Press (5) to conrm hours setting and go on to

minutes.

6. Set alarm time minutes by pressing (4) or (6). Press (5) to conrm hours setting and go on

to alarm type.

7. Set alarm type by pressing (4) or (6). Sources are:

- BEEP Tone 1

- BEEP Tone 2

- DAB

- FM

- iPod

8. Press (5) to conrm alarm type setting.

9. In Standby mode your Retro DAB+ will show bell symbols and numbers to show which alarms are active.

To show alarm status

In either standby or working modes press SNOOZE( 9) to select ALARM 1. Press it again to select ALARM

2. In either case the status of the alarm will be displayed:

Stopping or snoozing the alarm

When alarm goes off you can press (1) to turn off the alarm

Press SNOOZE (9) to snooze for 5 minutes. Your Retro DAB+ will enter into Standby mode and show the

clock. You can repeat snoozing for a maximum period of 1 hour.

Snoozing multiple alarms

Only one alarm can be snoozing at a time. If ALARM 1 is snoozing ALARM 2 will also automatically snooze if

it begins to sound. ALARM 1 snooze will be cancelled.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

View Quest Retro Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von View Quest Retro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info