Bedienungsanleitung Viking GE 150 (Seite 41 von 548) (Alle Sprachen)

667349

Zoom out

Zoom in

Vorherige Seite

1/548

Nächste Seite

DEFRNLITESPTNOSVFIDAPLSLSKHU EN

0478 201 9906 D - EN

7.2 Installing the chassis and

ejection chute

1 Install the ejection chute

extension

● Place the basic unit (A) onto a block of

wood with a height of approx. 15-

20 cm.

● Engage the hooks (1) of the ejection

chute extension (O) into the

openings (2) on the rear of the basic

unit (A) and turn the extension

downwards so that the front part of the

basic unit is precisely inserted in the

opening of the ejection chute extension.

● Fasten the screws (U) in the lugs of the

hooks (1) (1 - 2Nm).

2 Attach the chassis

● Press square nuts (K) and washers (L)

in the recesses provided on the basic

unit (3).

● Push the chassis with both wheel

carriers (4) up to the stop in the guides

on the basic unit (5).

● Push bent section of wheel carrier (6)

into the recess on the ejection chute

extension (7).

● Insert the screws (M) with washers (L)

the openings in the wheel carriers (8)

and fasten using combination

spanner (V) (4 - 6Nm).

3 Install strip

● Position the strip (P) and fasten

screws (R) (1 - 2Nm).

● Lift machine into upright position.

4 Install the discharge flap

● Attach the discharge flap (N) and press

in pin (Q) (use a plastic hammer if

necessary).

Ensure that the ribs (9) inside the

discharge flap on the left and right are

all correctly located in the guide groove

of the ejection chute extension (10).

7.3 Opening and closing the

discharge flap

Opening the discharge flap:

● For shredding, fold the discharge

flap (1) upwards and allow the tab (2) to

engage in the ejection chute extension.

Closing the discharge flap:

● For transport or space-saving storage,

lift the tab (2) slightly and fold away the

discharge flap (1) downwards.

7.4 Installing upper chute

● Place the upper chute (S) onto the

lower chute (3) with the symbol (1)

facing forwards in the direction of the

closure screws (2).

● Fasten the screws (T) in the order

shown (1 2 3 4).

8.1 What material can be processed?

– Feeding the garden shredder. (Ö 8.8)

GE 150, GE 250 S, GE 260 S:

Tree and hedge cuttings and thick branch

material with side shoots.

GE 250, GE 260:

Organic plant trimmings such as fruit and

vegetable cuttings, flower cuttings, leaves,

tree and hedge cuttings, as well as thick

branches with side shoots and twigs.

8.2 What material cannot be

processed?

Stones, glass, bits of metal (wire, nails,

etc.) or plastic must not be fed into the

garden shredder.

As a general rule:

Any materials that do not belong on the

compost heap should not be processed

using the garden shredder.

8.3 Maximum branch diameter

The data relates to freshly cut branch

material:

Maximum branch diameter

GE 150, GE 250, GE 250 S: 35 mm

GE 260, GE 260 S: 40 mm

The bent section of the wheel

carrier (6) must be precisely

inserted in the recesses on the

ejection chute extension (7).

The funnel can only be installed by

a specialist dealer using special

tools. VIKING recommends VIKING

specialist dealers.

In order to prevent the splash guard

from slipping off, we recommend

that the indicated assembly

sequence be observed.

8. Notes on working with the

machine

Tree and hedge cuttings should be

processed when fresh, as the

shredding performance is better

with fresh than with dried-out or wet

material.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Viking GE 150 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info