Bedienungsanleitung Viking GE 150 (Seite 46 von 548) (Alle Sprachen)

667349

Zoom out

Zoom in

Vorherige Seite

1/548

Nächste Seite

0478 201 9906 D - EN

1 Reversible blades

● On the blades, measure the

distance (A) between the bore and the

edge of the blade at several points.

Minimum distance:

A=6mm

2 Wing blade

● Measure the blade width (B) at the

upward-pointing curved edge of the

wing blade.

Minimum blade width:

B=15mm

3 Wing blade (GE 250, GE 260)

● Measure the blade width (C) at the

upward-pointing curved edge of the

wing blade.

Minimum blade width:

C=19mm

4 Shredding blade (GE 250, GE 260)

● Measure the blade width (D) at the

upward-pointing curved edge of the

shredding blade.

Minimum blade width:

D=13mm

11.8 Reversing the blades

● Remove the blade set. (Ö 11.5)

● Unscrew screws (1) and remove

together with nuts (2).

● Remove blade (3) upwards.

● Clean the blade disc.

● Reverse blade (3) and place onto the

blade disc with the sharp edge exposed

and align the bores.

● Insert screws (1) through the bores and

screw on nuts (2). Tighten the nuts (2)

to 10 Nm.

● Install the blade set. (Ö 11.6)

Sharpening the blades:

Blades which are blunt on both sides must

be sharpened before resuming work.

In order to ensure optimum machine

operation, the blades should only be

sharpened by a technician. VIKING

recommends VIKING specialist dealers.

● Remove the blades for sharpening.

● Cool the blades when sharpening,

e.g. with water. The blade must not be

allowed to display blue colouring, as

this would reduce its cutting quality.

● Sharpen the blade evenly to prevent

vibrations due to imbalance.

● Check blades for damage before

installing: The blades must be replaced

if notches or cracks are visible or if the

blades have reached the wear limits.

● Sharpen blades at a sharpening angle

of 30°.

● Sharpen the blades against the cutting

edge.

● After sharpening, remove any

sharpening burr at the cutting edge

using fine sandpaper.

● Observe the tightening torques

contained in the "Reversing the blades"

section when installing the blades.

11.9 Electric motor and wheels

The electric motor is maintenance-free.

The wheel bearings are maintenance-free.

11.10 Storage and winter break

Store the garden shredder in a dry and

locked place that is generally free of dust.

Make sure that the machine is kept out of

the reach of children.

Only store the garden shredder in good

operating condition and with the feed

chute fitted.

Note the following points when storing the

garden shredder for extended periods

(over winter):

● Thoroughly clean all external parts of

the machine.

● Thoroughly lubricate/grease all moving

parts.

12.1 Pulling or pushing the

garden shredder

● Hold the garden shredder at the

upper chute (1) and tilt to the rear.

● The garden shredder can be pulled or

pushed slowly (walking pace).

Blunt reversible blades may only be

reversed once. Always reverse

both blades.

12. Transport

Risk of injury!

Before transporting, carefully read

and observe the section "For your

safety", in particular the

"Transporting the machine" section.

(Ö 4.4)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Viking GE 150 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info