Bedienungsanleitung Viking MB 2R (Seite 38 von 424) (Alle Sprachen)

667219

Zoom out

Zoom in

Vorherige Seite

1/424

Nächste Seite

0478 111 9926 C - EN

1 Setting the rear cutting height

● Set the required cutting height at the

rear axle (1).

For this purpose, support the machine

with one hand and move the rear axle to

the desired level on one side first and

then on the other.

Ensure that the left and right sides are

at the same level (rear axle parallel to

the housing).

2 Setting the front cutting height

● MB 2 RT:

Push the cutting height adjustment

lever (2) outwards, move to the desired

level and allow it to engage.

● MB 2 RC, MB 2 R:

Set the required cutting height at the

front axle (3).

For this purpose, support the machine

with one hand and move the front axle

to the desired level on one side first and

then on the other. Ensure that the left

and right sides are at the same level

(front axle parallel to the housing).

The machine is equipped with several

safety devices for safe operation and for

the prevention of improper use.

9.1 Motorstop lever

The lawn mower is equipped with a

motorstop device.

The engine stops when the motorstop

lever is released during running operation.

The engine and blade come to a standstill

within 3 seconds.

Measuring the run-on time

Following engine start-up, the blade

rotates and a wind noise is audible. The

run-on time corresponds to the duration of

the wind noise after the engine stops. This

can be measured using a stopwatch.

10.1 General information on mulching

During mulching, the cut grass is chopped

up several times through a special air flow

guidance system in the mower blade area

and then blown back into the turf. The

clippings remain on the lawn.

Benefits

The decomposing clippings return organic

nutrients to the soil, serving as a natural

fertiliser.

Advantages

Emptying the grass catcher box and

disposal of the clippings are dispensed

with. Weed growth is slowed down and

significant amounts of fertilizer are saved.

10.2 When is mulching permissible?

VIKING recommends mulching only when

the lawn is dry and the grass is not too

high.

If the grass is too high, the lawn should be

mowed in two stages. (Ö 10.3)

10.3 How should mulching be

performed?

Requirements for good mulching results:

– Set the optimal cutting height: A third of

the grass height should be cut.

– Use well sharpened blades.

– Vary the mowing direction and ensure

that the mowing strips overlap.

Working method in high grass

In high grass, the lawn should be cut in two

stages.

First stage:

The lawn is mowed at the maximum

cutting height.

Second stage:

12 to 24 hours after the first stage, mulch

the lawn to the desired grass height at right

angles to the first mowing direction.

9. Safety devices

Risk of injury!

If a safety device is found to be

defective, the machine must not be

operated. Consult a specialist

dealer; VIKING recommends

VIKING specialist dealers.

Risk of injury!

If the run-on time of the blade

exceeds this delay, stop using the

machine and take it to your

specialist dealer.

10. Notes on working with

the machine

Caution

If the cutting height is too low or the

grass is wet, the housing may

become clogged, blocking the

blade!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Viking MB 2R Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info