Bedienungsanleitung Viking ME 443 (Seite 39 von 250) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch)

667214

Zoom out

Zoom in

Vorherige Seite

1/250

Nächste Seite

DEFRNLITESPTNOSVDAELRU EN

0478 121 9920 D - EN

ME 443, ME 443 C:

ME 443:

ME 443 C:

7.1 General

● Place the machine on level and firm

ground when performing all the

operations described.

7.2 Installing mono handlebar

(ME 443 C)

● 1 Insert sleeve (J) in the bore

on handlebar (1).

● 2 Fit two washers (L) with the convex

side facing inwards onto the sleeve.

● 3 Hold sleeve (J) and washers (L) and

insert together with handlebar (1) into

handlebar console (2).

● 4 Insert nut (M) into the handlebar

console as shown.

● 5 Insert bolt (K) from the outside

inwards through the bores in

handlebar (1) and in handlebar

console (2) and tighten.

Tightening torque:

18 - 22 Nm

Installing electric cable:

● Press electric cable (3) into the holders

on the handlebar console and

handlebar (4, 5) as shown and fasten to

the handlebar using cable clip (6).

7.3 Installing dual handlebar

(ME 443)

● Insert screw (F) through the bore

in cable guide (G).

● Fit upper handlebar (2) onto lower

handlebar sections (1).

● Attach cable guide (G) to electric

cable (3) and insert screw (F) through

the bore from the inside outwards.

● On the opposite side, insert screw (F)

from the outside inwards through the

bores.

● Fit handlebar protection (I) and screw

quick clamping devices (E) onto

screws (F) (the screw should project by

about one screw thread turn) and fold

upwards.

● Check correct assembly:

Quick-clamping devices (E) must be

sufficiently tightened so that they are

pressed tightly against the handlebar

and the upper handlebar is firmly

connected to the lower handlebar.

If the handlebar is not firmly installed or

the quick-clamping devices are not

correctly located, open the quick-

clamping devices and turn them until

they are securely fastened.

● Insert electric cable (3) into holder (4) of

the handlebar console as shown.

Installing cable clip:

● Press cable clip (H) onto the upper

handlebar. Distance between the cable

clip and switch:

25 - 27 cm

Insert electric cable (3) into cable

clip (H) as shown, close tab (5) and

allow it to engage.

6. Standard equipment

Item Designation Qty.

A Basic unit 1

B Upper part of grass catcher

box

C Lower part of grass catcher

box

D Pin 2

• Instruction manual 1

E Quick-clamping device 2

F Screw 2

G Cable guide 1

H Cable clip 1

I Handlebar protection 2

J Sleeve 1

K Screw 1

L Washer 2

M Nut 1

The standard equipment may vary

depending on the country and

version type.

7. Preparing the machine for

operation

Risk of injury!

Observe the safety instructions in

the section "For your safety" (Ö 4.).

Danger of electric shock!

In order to prevent damage to the

insulating layer on the handlebar,

only press on the cable clips by

hand. Do not use any tools (e.g.

hammer or screwdriver).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Viking ME 443 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info