Bedienungsanleitung Visonic PowerMax Express (Seite 15 von 36) (Englisch)

580333

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

D-302989 15

4.4.19 Jam Detect

(Fig. 4.4, location 19). Here you determine whether

jamming (interfering transmissions, on the radio channel

used by the system) will be detected and reported or not.

If a jam detection option is selected, the system does not

allow arming under the relevant jamming conditions.

Jam Detection Options

Option Detection and Reporting when

UL (20/20)

(USA standard)

There is continuous 20 seconds of

jamming

EN (30/60)

(Europe standard)

There is an accumulated 30 seconds of

jamming within 60 sec.

class 6 (30/60)

(British standard)

Like EN (30/60) but the event will be

reported only if the jamming duration

exceeds 5 minutes.

Disabled (No jamming detection and reporting).

4.4.20 Latchkey

(Fig. 4.4, location 20). Here you determine whether the

system can be armed in the latchkey mode. If the system

is armed this way, a “latchkey” message will be sent to

specific telephones upon disarming by a “latchkey user”

(users 5-8 or keyfob transmitters 5-8). This mode is useful

when parents at work want to be informed of a child’s

return from school. The options are: Latchkey ON and

Latchkey OFF.

4.4.21 “Not Active”

(Fig. 4.4, location 21). Here you determine the time limit for

reception of signals from sensors used to monitor the

activity of sick, elderly or disabled people. If no sensor

detects and reports movement at least once within the

defined time limit, a “not-active” alert is initiated.

Options: 3, 6, 12, 24, 48, 72 hours and no act disable.

4.4.22 Back Light (Optional)

(Fig. 4.4, location 22). Here you determine whether the

keypad back lighting will remain on at all times or will turn

on when a key is pressed and turn off within 10 seconds if

no further keystrokes are sensed.

The two options are: always on and off after 10 s.

Note: Back Light can be used only if this option is

available on the purchased control panel.

4.4.23 Duress

(Fig. 4.4, loc. 23). A duress alarm (ambush) message can

be sent to the central station if the user is forced to disarm

the system under violence or menace. To initiate a duress

message, the user must disarm the system with the duress

code (2580 by default). Here you can change the code

digits or enter "0000" to disable the duress feature. The

system does not allow the user to program the duress

code saved in this memory location as an existing user

code.

4.4.24 Piezo Siren

(Fig. 4.4, location 24). Here you determine whether the

internal siren will sound or remain silent upon alarm

(according to the user preference). Options: piezo siren

on, piezo siren off.

4.4.25 Reset Option

(Fig. 4.4, location 25). (Not applicable in the USA)

Here you determine whether the system can be rearmed

(after an event) by the user or only by the installer.

Options: user reset or engineer reset.

If Engineer Reset is selected, the system can be rearmed

only by the installer

; by entering and exiting the installer

menu, by entering and exiting the event log (see section 7),

or by remote telephone. To perform Engineer Reset via the

telephone, establish communication with the

PowerMaxExpress (see user guide, par. 6.3A, steps 1-5)

and continue as follows:

a.  [*], [installer code], [#]

b. Wait for 2 beeps

c.  [*], [1], [#]

d.  [*], [99], [#]

4.4.26 Tamper Option

(Fig. 4.4, location 26). Here you determine whether zone

tamper will be reported or ignored. Available options are:

zone tamper ON and zone tamper OFF.

Note: To comply with EN requirements, "zone tamper ON"

must be selected.

4.4.27 Siren On Line

(Fig. 4.4, location 27).

Here you determine whether the

siren will be activated or not when the telephone line fails

during system armed state. Available options are: enable

on fail, disable on fail.

4.4.28 Memory Prompt

(Fig. 4.4, location 28). Here you determine whether the user

will receive indication that an alarm has been activated.

Available options are: enable and disable.

4.4.29 Disarm Option

(Fig. 4.4, location 29).

Here you determine when it is possible

to disarm the system:

A. Any time.

B. In AWAY mode, during entry delay, by using the

PowerMaxExpress keypad or wireless sensor (keyfob).

C. In AWAY mode, during entry delay, by using a wireless

device (keyfob) only (this is set as a default in UK to

comply with DD243).

D. During entry delay, or by using the PowerMaxExpress

keypad in AWAY mode.

Options: any time, on entry all, on entry wireless, or

entry + away kp.

4.4.30 Bell/Rep. Option

(Fig. 4.4, location 30). Here you determine whether an

alarm will be initiated (siren / report) when there is a

supervision / jamming failure during AWAY arming state.

Available options are: EN standard and other. When "EN

standard" is selected, if there is supervision / jamming

failure during AWAY arming, the siren is activated and the

events are reported as tamper events. When "Other" is

selected, there is no such activity during AWAY arming.

4.4.31 Low-Bat Ack

(Fig. 4.4, location 31). Here you determine whether the user

will hear or will not hear low battery sound when he tries to

disarm the system with a keyfob whose battery voltage is

low. Available options are: keyfob L-B on (the user has to

acknowledge the keyfob low battery message) or keyfob

L-B off (the user does not have to acknowledge the keyfob

low battery message).

4.4.32 Screen Saver

(Fig. 4.4, location 32). Here you can determine that if no

key is pressed during more than 30 seconds, the display

will be “PowerMax” (to prevent possible intruder of

knowing the system status). You can determine that

normal display will return after pressing the

button followed by entering user code (Refresh by Code)

or after pressing any key (Refresh by Key).

Visonic PowerMax Express Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Visonic PowerMax Express

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info