Bedienungsanleitung Visonic PowerMax Express (Seite 19 von 36) (Englisch)

580333

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

D-302989 19

Key Functionality

Moves the cursor from left to right.

Long press for speed.

Moves the cursor from right to left.

Long press for speed.

Scrolls upward the sequence of inserted digits.

Long press for speed.

Scrolls downward the sequence of inserted digits.

Long press for speed.

Places cursor to extreme right position of edit string

and shows the last 16 digits of edit string.

Reverts to previous or top menu without saving the

edit string.

Reverts to "<OK> TO EXIT" without saving the edit

string.

Saves and reverts to previous menu.

Clears all digits to the right of cursor.

Clears one digit by cursor.

Selects between uppercase or lowercase digits.

PIN Code [Fig 4.5.2(7)]

Enter PIN code of the SIM card installed in the

PowerMaxExpress unit (up to 16 digits).

Force Home Network [Fig 4.5.2(8)]

Here you determine whether to force the SIM card to use

the home network only and not to select another network in

case the home network cannot be found.

The options are: disable and enable.

LAN Settings [Fig 4.5.2(9)]

Note: The LAN Settings menu appears only if a

Broadband Module exists in the PowerMaxExpress alarm

system.

Enable DHCP [Fig 4.5.2(9a)]

Here you determine whether to obtain an IP address

automatically using a DHCP server or to enter an IP

address manually.

Toggles between DHCP enable and DHCP disable.

Note: When DHCP is enabled, the last IP number will be

changed to 200. In other words, it will take the form

xxx.xxx.xxx.200.

Manual IP [Fig 4.5.2(9b)]

Here you manually enter LAN parameters.

IP address – the IP address of the Broadband Module.

Subnet mask – the subnet mask used with the IP

address.

Default GW – the default gateway of the Broadband Module.

Note: If DHCP is set to enabled the above entries will be

ignored.

Transport Protocol

(Applicable in the USA only)

[Fig 4.5.2(10)]

Here you select the type of protocol used by the control

panel to transfer data over the internet.

The options are: TCP and UDP.

Session Timeout [Fig 4.5.2(11)]

Here you determine whether the control panel will stay

continuously connected via GPRS communication, or,

temporarily connected to receive event reports only.

The options are: off on timeout and always ON.

4.5.3 C.S. Reporting (Fig. 4.5 Detail C)

Report Events [Fig 4.5.3(1)] – see note in Fig. 4.5 Detail C

Here you determine which types of event will be reported

to central stations. Due to lack of space in the display,

abbreviations are used: alarm is “alrm”, alert is “alrt” and

open/close is “o/c”. The asterisk (J) is a separator

between events reported to central station 1 and events

reported to central station 2.

Messages are divided by type into four groups:

No. Group Events Reported

1 Alarms Fire, Burglary, Panic, Tamper

2 Open/close Arming AWAY, Arming HOME,

Disarming

3 Alerts No-activity, Emergency, Latchkey,

Gas, Flood, Temperature

4 Maintenance Low-battery AC failure

"Alarm" group has the highest priority and "Alert" group

has the lowest priority.

The selectable options are as follows:

Plan name Sent to center 1 Sent to center 2

all -o/c J backup All but open/close

All but open/close if center 1

doesn’t respond

all J all All All

all-o/c J all -o/c All but open/close All but open/close

all –o/c J o/c All but open/close Open/close

all (–alrt) J alrt All but alerts Alerts

Alrm J all (–alrm) Alarms All but alarms

Disable report Nothing Nothing

all J backup All All if cent. 1 doesn’t respond

Note: “All” means that all 4 groups are reported and also

trouble messages - sensor / system low battery, sensor

inactivity, power failure, jamming, communication failure etc

1st Report Method [Fig 4.5.3(2)]

Here you define the 1st priority of method used to report

events. The options are: disable, broadband, cellular

and PSTN.

2nd Report Method [Fig 4.5.3(3)]

Here you define the 2

priority of method used to report

events. If the method defined to report events in the 1st

priority fails, the control panel will attempt to report using

the method defined in the 2nd priority (see notes in 1

Report Method).

The options are: disable, broadband, cellular and PSTN.

3rd Report Method [Fig 4.5.3(4)]

Here you define the 3

priority of method used to report

events. If the method defined to report events in the 2

priority fails, the control panel will attempt to report using

the method defined in the 3rd priority (see notes in 1

Report Method).

The options are: disable, broadband, cellular and PSTN.

Dual Reporting [Fig 4.5.3(5)]

Here you determine whether to report events using PSTN

and cellular at the same time instead of waiting for the 1

method to fail before trying the 2

method.

The options are: disable and PSTN & cellular, PSTN &

broadband and broadband & cellular.

Receiver 1 Account No. [Fig 4.5.3(6)] - see note in

Fig. 4.5 Detail C

Here you enter the number that will identify your specific

alarm control system to the 1

central station. The number

consists of 6 hexadecimal digits.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic PowerMax Express Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Visonic PowerMax Express

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info