Bedienungsanleitung Vivitek DW868 (Seite 4 von 74) (Englisch)

594850

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

DLP Projector—User’s Manual

— iv —

Verify Installation Location

 To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper

grounding and equalized ground potential for all of the equipment in the Projector System.

 The power code provided with the Projector should be used. In case of any missing item, other

qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use

2-blade power cord.

 Verify if the voltage is stable, grounded properly and there is no electricity leakage.

 Measure total power consumption which should not higher the safety capacity and avoid safety

issue and short circuit.

 Turn on Altitude Mode when located in high altitude areas

 The projector can only be installed upright or inverted.

 When installation the bracket, make sure the weight limit is not exceed and firmly secured.

 Avoid installing near air conditioner duct or subwoofer.

 Avoid installing at high temperature, insufficient cooling and heavy dust locations.

 Keep your product away from fluorescent lamps to avoid malfunction

caused by IR interference

 The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted

tightly, with the screws on both sides securely fastened to ensure proper connection of the signal

wire for achieving optimal display effect.

 The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected

to AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even

DAMAGE the port.

 Install the projector above 200cm to avoid damage.

 The power cord and signal cable should be connected before power on the projector. During the

projector starting and operating process, DO NOT insert or remove the signal cable or the power

cord to avoid damaging the projector.

Cooling notes

Air outlet

 Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.

 Air outlet location should not be in front of the lens of other projector to avoid causing illusions.

 Keep the outlet at least 100cm away from the inlets of other projectors

 The projector generates a massive amount of heat during use. The internal fan dissipates the heat

of the projector when shutting down, and such process may continue for a certain period. After the

project enters STANDBY MODE status, press the AC power button to turn off the projector and

remove the power cord. DO NOT remove the power cord during the shutdown process, as it may

cause damage to the projector. In the meantime, the delayed heat radiating will also affect the

service life of the projector. The shutdown process may vary depending on the model used.

Whatever the case may be, be sure to disconnect the power cord till after the projector enters the

STANDBY status.

Air inlet

 Make sure there is no object blocking air input within 30 cm.

 Keep the inlet away from other heat sources

 Avoided heavy dust area

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vivitek DW868 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info