Bedienungsanleitung VNT DOGtrace d-fence (Seite 8 von 13) (Englisch)

626251

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

With your transmitter you can extend and reduce the width of the warning and correcting

zones, depending on conditions in your piece of land and upon how the wire is laid.

a) The warning zone (sound signal)

It is inﬁ nitely adjustable from 0,40 m to 5 m (the detection distance is approximate, depen-

ding on the loop length and location of the wire) along both sides of the wire using the

knob located on the transmitter panel. Steps 0 to 10 will help you deﬁ ne the zone width

according to your needs, whereas it approximately holds true that 0 = 0,40 m and 10 = 5 m.

b) The correcting zone (pulses)

It is inﬁ nitely adjustable from 0,30 m to 1,50 m (the detection distance is approximate,

depending on the loop length and location of the wire) along both sides of the wire. Steps

0 to 10 will help you deﬁ ne the one width according to your needs, whereas it approxi-

mately holds true that 0 = 0,30 m and 10 = 1,5 m.

c) Checking and setting the zones

Before you let your dog enter its restricted area, you should physically check the surface

and boundaries of your piece of land assigned to your pet. For this purpose, ﬁ rst place the

leads of the testing discharge lamp under the electrodes of the receiving collar; release

them slightly and then fasten them slightly again so that they can press down the testing

lamp wires. Install a battery in the receiving collar and then power up the transmitter by

setting the switch to the left to “ON“. Set both potentiometer knobs to ”0“ position.

Correcting zone setting

Select a distance from the antenna wire where you wish to deﬁ ne the correcting zone for

your dog, stand up on that place and hold the receiving collar by the strap about 30 cm

above ground with the logo facing to the antenna wire.

Then, turn slowly the potentiometer to adjust the correcting zone as long as the test LED is

regularly on in given intervals (approximately after 1 second) along with audible sound signal.

Warning zone setting

The procedure is the same as the previous one. Select a distance from the antenna wire

where you wish to deﬁ ne the warning zone for your dog, stand up on that place and hold

the receiving collar by the strap about 30 cm above ground with the logo facing to the

antenna wire. Then, turn slowly the potentiometer to adjust the warning zone as long as

a rapid intermittent sound signal is heard.

Important:

The zone width is changed according to the length and location of the antenna wire

in your piece of land. The longer the antenna wire is, the narrower are the zones.

The longer the antenna wire is, the narrower the zones are. The width may also be

diﬀ erent at the bends (in the corners) compared to straight sections.

Zone width setting (”warning“ and ”correcting“ zones)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

VNT DOGtrace d-fence Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info