Bedienungsanleitung Volkswagen Touareg 2015 (Seite 672 von 684) (Englisch)

708062

672

Zoom out

Zoom in

Vorherige Seite

1/684

Nächste Seite

The procedure for attaching and for removing the jumper cables is described below. Perform each of

the following steps only in the order in which it is described.

Before you begin

 Switch off the ignition in both vehicles.

 Open the hoods of both vehicles.

 Remove the cover from the positive terminal on your vehicle and, if necessary, the battery cover of

the other vehicle.

Diagram A: Attaching jumper cables

Diagram A applies where the vehicle with the dead battery has jump-start terminals (1) and is being

jump-started by a vehicle whose battery is in the engine compartment (2) ⇒ .

1. Attach one end of the red jumper cable to the positive jump-start terminal

(+) of the vehicle with

the dead battery (1).

2. Attach the other end of the red jumper cable to the positive terminal

(+) of the booster battery (2).

3. Connect one end of the black jumper cable to a suitable ground connection

(3) on the vehicle with

the booster battery

(2). A suitable ground connection is a solid metal part bolted directly to the en-

gine block of the vehicle with the booster battery or this vehicle's engine block itself.

4. Attach the other end of the black jumper cable to the negative jump-start terminal

(-) of the

vehicle with the dead battery

(1).

Diagram B: Attaching jumper cables

Diagram B applies where the dead battery (1) is in the engine compartment of the vehicle being jump-

started, and the vehicle providing starting assistance has jump-start terminals

(2) ⇒ .

1. Attach one end of the red jumper cable to the positive terminal

(+) of the dead battery (1).

2. Attach the other end of the red jumper cable to the positive jump-start terminal (+) of the vehicle

providing starting assistance (2).

3. Attach one end of the black jumper cable to the negative jump-start terminal

(-) of the vehicle

providing starting assistance (2).

4. Connect the other end of the black jumper cable to a suitable ground connection (3) on the vehicle

with the dead battery

(1). A suitable ground connection is a solid metal part bolted directly to the

engine block of the vehicle with the dead battery or this vehicle's engine block itself.

Diagram C: Attaching jumper cables where both vehicles have jump-start terminals

Diagram C applies where the vehicle with the dead battery has jump-start terminals (1) and is being

jump-started by a vehicle that also has jump-start terminals (2) ⇒ .

1. Attach one end of the red jumper cable to the positive jump-start terminal

(+) of the vehicle with

the dead battery (1).

2. Attach the other end of the red jumper cable to the positive jump-start terminal

(+) of the vehicle

providing starting assistance (2).

3. Attach one end of the black jumper cable to the negative jump-start terminal

(-) of the vehicle

providing starting assistance (2).

4. Attach the other end of the black jumper cable to the negative jump-start terminal (-) of the

vehicle with the dead battery

(1).

Starting the engine

1. Start the engine of the vehicle with the good battery that is providing help and let it run at idle

speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Volkswagen Touareg 2015 Seite 672

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info