Bedienungsanleitung Voltcraft 2127443 (Seite 5 von 12) (Deutsch, Englisch, Holländisch, Französisch)

738481

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

b) Additional information on lithium rechargeable batteries

• Li-Ion batteries installed in this device require special care during charging/discharging, ope-

ration and handling.

• Never destroy or damage the rechargeable battery, do not drop it or puncture it with any

objects. Protect the rechargeable battery from mechanical stress. This may cause a re or

explosion!

• Ensure that the device does not overheat during use, charging, discharging, transport and

storage. Do not place the device near heat sources and protect it from exposure to direct

sunlight. If the device overheats, there is a risk of re and explosion!

• The device must not exceed a temperature of +60 °C.

• If a device is damaged or the outer cover is puffed/swollen, discontinue use of the device. Do

not recharge it. This may cause a re or explosion!

Overview of parts

56 7

START

ERR

1 Button for charge level indicator and activation of LED light and power bank function

2 Charge level indicator

3 Protective cover

4 LED light

5 Micro USB charging input “Input”

6 USB charging output “Output”

7 Mechanically coded connection for starter cable

8 MOSFET housing with LED status indicator for starter operation

9 Mechanically coded plug for quick start system

10 Pole terminals (red +, black -)

Start-up and charging

• The quick start system must be fully charged before use.

• Standard USB quick chargers with a charging current of at least 1 A are suitable for char-

ging. An output charging current of at least 1.5 A is recommended because it shortens the

charging time.

• Connect the included charging adapter cable to the USB charger (not included).

• Plug the Micro USB cable into the Micro USB charging input “Input” (5).

• As soon as your USB charger provides sufcient charging current, the charging process

is indicated by the LEDs of the charge level indicator (2), which light up one after another.

• If all 4 LEDs of the charge level indicator light up at the same time or are permanently lit, the

charging process is completed.

• Remove the charging cable from the start system.

• Briey press the activation button (1) to display the current charge status.

View Meaning

4 LEDs Start system is fully charged and can be used without restriction.

3 LEDs Start system is 75% charged and can be used without restriction.

2 LEDs Start system is 50% charged. It can only be used as power bank or LED light.

1 LED Start system is 25% charged. It can only be used as power bank or LED light.

0 LED Start system is not ready for use and must be charged.

Operation

a) Start support function

The quick start system can support a weak starter battery when starting the engine. During

start-up a very high current is needed. The quick start system emits multiple high current pulses

during the start-up phase. This is usually enough to support a weak starter battery.

Never short-circuit the two pole terminals. This will discharge the quick start system

and damage the rechargeable battery.

To perform start-up, proceed as follows:

• Check the charge status of the quick start system. For a start-up support at least 3 LEDs

must light up. If fewer LEDs are lit, the quick start system must rst be charged.

• Open the protective cover (3) on the quick start system.

• Insert the starter cable plug (9) into the connection for the starter cable (7). The plug is

mechanically coded and ts together only with the correct polarity. Ensure rm and reliable

contact.

• The green LED status indicator on the MOSFET housing (8) starts to ash.

• Connect the red pole terminal (10) to the plus pole (+) and the black pole terminal (10) to

the minus pole (-) of the car battery. Ensure that the contact is connected properly. Turn the

terminals back and forth to break possible oxide layers on the poles.

• Once the contact is established, the green LED glows steadily after a few seconds and you

will hear a short beep. Start your car within 30 seconds. The quick start system now emits

multiple current pulses during the start-up phase. They should be enough to start the engine.

• When the engine starts, disconnect the quick start system and remove the starter cable from

the quick start system. Close the connections with the protective cover.

• If the engine does not start, disconnect the quick start system. Wait approx. 5 minutes and

then repeat a start-up operation.

• If the engine still does not start after three attempts, the start support process must be termi-

nated. Probably, the car battery is defective, or there is another problem. In this case, have

the vehicle checked by a specialist workshop.

LED status indicator on the MOSFET housing (8)

View Meaning

Green ashing Quick start system is ready

Green steady light with beep Start mode is activated

Red steady light Connection error. Please check all contacts

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Voltcraft 2127443 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info