Bedienungsanleitung Voltomat Heating BH-117327.3 (Seite 100 von 201) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

701479

100

Zoom out

Zoom in

Vorherige Seite

1/201

Nächste Seite

- 99 -

Note:

1) The weekly program is continuous, which means that it returns to day 1 at the end of day 7. If that is not

what you want, you should turn the weekly program off.

2) To check the settings, press “DAY”, “EDIT”, “TIME/ON” then “TIME/OFF”. The display will show the

settings.

3) The timer can only be set to hours, not minutes.

4) The stop time must always be later than the start time.

5) Your settings will be lost if the appliance is switched off by pressing the power switch, if there has been a

power cut or if the plug has been removed from the socket. Press button “SET” to check the day and time

and set them again if necessary.

SET OPEN WINDOW DETECTOR

1. Make sure the unit is switched on.

2. Press button “ ”; the display shows icon “ ”. The standard temperature is 23 °C; you can press plus

and minus buttons “ / ” to choose your desired temperature.

3. When the open window detection is switched on, the appliance will switch off if the temperature in the

room drops by between 5 and 10 degrees within 10 minutes, and go to standby mode.

4. In this case, you can turn the appliance on again by pressing the on/off button “ ”. Press the button

“ ” again to turn the open window detection off. The icon “ ” disappears from the display and the

unit returns to its previous settings.

5. If both the weekly programme and the open window detection are on, the open window detection will

only work while the appliance is switched on in the weekly program.

OVERHEATING PROTECTION

The overheating protection system switches the unit off if it gets too hot. Common reasons for this are that

the unit has been partially or completely covered, the intake/outlet are blocked or the unit has been placed

too close to a wall. If the overheating protection is activated and the unit switches off, the unit will start to

ventilate to get rid of the extra heat. In this case, the display does not change. Once the unit has cooled down,

it will return to its previous setting. We advise to switch the unit off using the remote control and to give it

enough time to cool down. Once you have removed the cause of the overheating, you can use the unit again

as normal. If you cannot find the cause of the overheating and the unit continues to overheat, you should turn

the unit off and return it for repair.

MAINTENANCE

 Before you clean the unit, turn off the switch. Remove the plug from the socket and wait until the fan

heater cools down completely.

 Use a damp cloth to wipe the heater housing.

 Clean the air inlet / outlet grills frequently with a soft dry cloth.

 Do not use detergents, abrasive cleaning liquids or chemicals (alcohol, gasoline etc.) to clean the

appliance.

 Do not allow the interior to get wet as this could create a hazard.

 To store away the heater, put the heater back into its original package and store it in a clean dry place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Voltomat Heating BH-117327.3 Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info