Bedienungsanleitung Volvo V70 - 2000 (Seite 93 von 102) (Englisch)

484482

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

2000 Volvo S & V70

http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_11.htm[4/4/2013 10:25:25 PM]

If, after several attempts, you do not successfully program the HomeLink® Universal Transceiver to learn the signal of

the hand-held transmitter, refer to the section "Programming rolling codes" or call the toll-free customer assistance

number: 1-800-355-3515 (Internet: www.HomeLink.jci.com).

WARNING!

· If you use the HomeLink® Universal Transceiver to open a garage door or gate, be sure that no one is near the

gate or door while it is in motion.

· Do not use the HomeLink® Universal Transceiver with any garage door opener that lacks safety "stop" and

"reverse" features as required by federal safety standards. (This includes any garage door opener model

manufactured before April 1, 1982). A garage door opener which cannot "detect" an object, signalling the door to

"stop" and "reverse" does not meet current federal safety standards. Using a garage door opener without these

features increases the risk of serious injury or death. For more information on this matter, call toll-free 1-800-355-

3515 (Internet: www.HomeLink.jci.com

pg. 199 HomeLink® Universal Transceiver (option)

NOTE - Canadian residents:

During programming, your hand-held transmitter may automatically stop transmitting. To train your hand-held

transmitter, continue to hold the HomeLink® button (see steps 2, 3 under "Programming the transceiver") while you

press and repress ("cycle") your hand-held transmitter button every two seconds until the frequency signal has been

learned. The HomeLink® indicator light will flash slowly and then rapidly to indicate that the HomeLink® button has

been successfully programmed.

Programming rolling codes

Determine, in one of the following ways, if your garage door uses a rolling code system and is manufactured after

1996:

· Refer to the garage door opener's owner's manual for verification.

· The hand-held transmitter appears to program the HomeLink® Universal Transceiver but the transceiver does not

activate the garage door.

· Press the programmed HomeLink® button. The garage door opener has the rolling code feature if the HomeLink®

indicator light flashes rapidly and then glows steadily after approximately 2 seconds.

To train a garage door opener with the rolling code feature, follow these instructions after the transceiver has been

programmed (the aid of a second person may make the training quicker and easier):

1. Locate the training button on the garage door opener motor head unit. The exact location and color of the button

may vary. If you encounter difficulty, refer to the garage door opener owner's manual or call: 1-800-355-3515

(Internet: www.HomeLink.jci.com).

2. Press the "training" button on the garage door opener motor head unit until the "training" light comes on.

3. Firmly press and release the programmed HomeLink® button. Press and release the HomeLink® button a second

time to complete the training process.

Some garage door openers may require you to do this procedure a third time to complete the training.

The programmed button on your HomeLink® Universal Transceiver

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Volvo V70 - 2000 Seite 93

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Volvo V70 - 2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info