Bedienungsanleitung Vonroc AG503AC (Seite 10 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778559

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

WWW.VONROC.COM

6. Side handle connection point

7. Side handle

8. Allen key

9. Rear handle

10. Handle release knob

11. Spindle

12. Mounting ﬂange

13. Wheel disc (not included)

14. Clamping nut

15. Spanner

3. ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Assembling the protection guard (Fig. C and D)

1. Place the machine on a table with the spindle

(11) facing upwards.

2. Place the protection guard (3) over the machine

head as shown in Figure C making sure the ridg-

es on the protection guard fall into the notches

of the machine head.

3. Turn the protection guard counter clockwise as

shown in Figure D.

4. Fix the the allen screw (2) on the guard (3) with

the allen key (8).

5. You can adjust the position of the protection

guard by releasing the allen screw (2), adjust the

guard to the desired position and ﬁxing the allen

screw again.

Never attempt to remove the guard.

Mounting and removing the wheel disc (Fig. B)

Do not use the machine without the guard.

Only use sharp and undamaged wheel discs.

• Always use suitable wheel disc for this machine

with diameter Ø 230 mm and a bore from 22.2

mm the thickness of the wheel disc should be

6 mm for wheel disc for grinding and 3 mm for

wheel disc for cutting, the mounting wheel disc

may not touch the safety guard.

Mounting

1. Place the machine on a table with the protection

guard (3) facing upwards.

2. Mount the ﬂange (12) onto the spindle (11).

3. Place the wheel disc (13) onto the spindle (11).

4. Keep the spindle lock button (1) pressed and

ﬁrmly tighten the clamping nut (14) onto the

spindle (11) by using the spanner (15).

Removing

1. Place the machine on a table with the protec-

tion guard (3) facing upwards.

2. Keep the spindle lock button (1) pressed and loos-

en the clamping nut (14) using the spanner (15).

3. Remove the wheel disc (13) from the spindle (11).

4. Keep the spindle lock button (1) pressed and

ﬁrmly tighten the clamping nut (14) using the

spanner (15).

Mounting the side handle (Fig. A and E)

• The side handle (7) can be screwed into one of

the three side handle connection points (6).

4. OPERATION

Make sure that the work piece is properly

supported or ﬁxed.

Rear handle (Fig. A)

Before rotating the handle, always switch

off the machine and remove the mains plug

from the mains.

1. To unlock the handle (9), push and hold the

handle release knob (10).

2. Rotate the handle (9) into one of the 3 available

positions and release the handle release knob

(10).

Before switching the tool on, ensure the

handle release knob (10) clicks and locks

into place when changing handle position.

Switching on and off (Fig. A)

• To switch the machine on, push the switch for-

ward and press the on/off switch (5).

• To switch the machine off, release the On/off

switch (5).

• Hold the machine away from the work piece

when turning it on and off because the wheel

disc could damage the work piece.

• Clamp the work piece ﬁrmly or use another meth-

od to ensure that it cannot move while working.

• Check the discs regularly. Worn wheel discs have

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc AG503AC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info