Bedienungsanleitung Vonroc CD505DC (Seite 7 von 56) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

763910

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

WWW.VONROC.COM

3. ASSEMBLY

Before any work on the power tool, remove

the battery.

The battery must be charged before ﬁrst use.

Inserting the battery into the machine (Fig. B)

Ensure that the exterior of the battery is

clean and dry before connecting to the

charger or machine.

Insert the battery (2) into the base of the machine

as shown in Fig. B.

2. Push the battery further forward until it clicks

into place.

Removing the battery from the machine (Fig. B)

1. Push the battery unlock button (3)

2. Pull the battery out of the machine like shown

in Fig. B.

Checking the battery charging status (Fig. C)

• To check the battery charge status, push the

button (12) on battery shortly.

•

The battery has 3 lights indicating the charge

level, the more lights that burn, the more charge

the battery has left.

•

When the lights are not burning it means the bat-

tery is empty and must be charged immediately.

Charging the battery with the charger (Fig. C)

1. Take the battery (2) from the machine.

2. Turn the battery (2) to upside down position and

slide it onto the charger (14) as shown in Fig. C.

3. Push the battery until it is fully pushed into the

slot.

Plug the charger plug into an electrical outlet and

wait for a while. The LED indicators on the charger

(15) will lighten up and show the charger status.

The charger has 2 LED indicators (15) which indi-

cate

the status of the charging process:

Red LED Status Green LED status Charger status

Off Off No power

Off On

Standby mode:

- No battery is

inserted or,

- Battery inserted

but charging has

ﬁnished

On Off Battery charging in

progress

• Fully charging the 2Ah battery may take up to

60 minutes.

• Fully charging the 4Ah battery may take up to

120 minutes.

After the battery is fully charged remove the char-

ger plug from the outlet and remove the battery

from the charger.

When the machine is not being used over a

longer period of time it is best to store the

battery in charged condition.

Fitting and removing drills or screwdriver bits (Fig. A)

The drill chuck (7) is suitable for drills and screw-

driver bits with round shaft as well as hexagonal

shaft.

1. Hold the machine ﬁrmly with one hand.

2. Open the drill chuck (7) by rotating the chuck

with your other hand in clockwise direction until

it is opened far enough for the bit to slide in.

3. Insert the shaft of the drill or screwdriver bit.

4. Tighten the drill chuck again by ﬁrmly rotating

the chuck (7) counterclockwise.

5. Check if the bit is centered well by shortly acti-

vating the machine´s on/off switch.

4. OPERATION

Adjusting the gears (Fig.A)

Never switch gears when the motor is

running, this will damage your machine.

Never put switch in the middle between both

positions, this will damage your machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CD505DC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info