Bedienungsanleitung Vonroc CS502AC (Seite 7 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778299

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

WWW.VONROC.COM

backward while the blade is in motion or kick-

back may occur. Investigate and take corrective

actions to eliminate the cause of blade binding.

• When restarting a saw in the workpiece, centre

the saw blade in the kerf and check that saw

teeth are not engaged into the material. If saw

blade is binding, it may walk up or kickback

from the workpiece as the saw is restarted.

• Support large panels to minimise the risk of

blade pinching and kickback. Large panels tend

to sag under their own weight. Supports must

be placed under the panel on both sides, near

the line of cut and near the edge of the panel.

• Do not use dull or damaged blades. Unsharpe-

ned or improperly set blades produce narrow

kerf causing excessive friction, blade binding

and kickback.

• Blade depth and bevel adjusting locking levers

must be tight and secure before making cut.

If blade adjustment shifts while cutting, it may

cause binding and kickback.

• Use extra caution when sawing into existing

walls or other blind areas. The protruding blade

may cut objects that can cause kickback.

Lower guard function

• Check lower guard for proper closing before

each use. Do not operate the saw if lower guard

does not move freely and close instantly. Never

clamp or tie the lower guard into the open posi-

tion. If saw is accidentally dropped, lower guard

may be bent. Raise the lower guard with the

retracting handle and make sure it moves freely

and does not touch the blade or any other part,

in all angles and depths of cut.

•

Check the operation of the lower guard spring.

If the guard and the spring are not operating

properly, they must be serviced before use. Lower

guard may operate sluggishly due to damaged

parts, gummy deposits, or a build-up of debris.

• The lower guard may be retracted manually

only for special cuts such as “plunge cuts and

angle cuts”. Raise the lower guard by retracting

the handle and as soon as the blade enters the

material, release the lower guard. For all other

sawing operations, the lower guard should

operate automatically.

•

Always observe that the lower guard is covering

the blade before placing saw down on bench or

ﬂoor

. An unprotected, coasting blade will cause

the saw to walk backwards, cutting whatever is

in its path. Be aware of the time it takes for the

blade to stop after switch is released.

ADDITIONAL SAFETY WARNINGS

• Do not reach into the chip ejector with your

hands. They could be injured by rotating parts.

• Do not work overhead with the saw. In this

manner you do not have sufﬁcient control over

the power tool.

• Use appropriate detectors to determine if utility

lines are hidden in the work area or call the lo-

cal utility company for assistance. Contact with

electric lines can lead to ﬁre and electric shock.

Damaging a gas line can lead to explosion. Pe-

netrating a water line causes property damage.

• Do not operate the power tool stationary. It is

not designed for operation with a saw table.

• Do not use high speed steel (HSS) saw blades.

Such saw blades can easily break.

• Do not saw ferrous metals. Red hot chips can

ignite the dust extraction.

• When working with the machine, always hold it

ﬁrmly with both hands and provide for a secure

stance. The power tool is guided more secure

with both hands.

• Secure the workpiece. A workpiece clamped

with clamping devices or in a vice is held more

secure than by hand.

• Always wait until the machine has come to a

complete stop before placing it down. The tool

insert can jam and lead to loss of control over

the power tool.

• Circular saws are intended to cut wood or

wood-like products, they cannot be used with

abrasive cut-off wheels for cutting ferrous ma-

terial such as bars, rods, studs, etc. Abrasive

dust causes moving parts such as the lower

guard to jam. Sparks from abrasive cutting will

burn the lower guard, the kerf insert and other

plastic parts.

• Use only saw blades that are marked with a

speed equal or higher than the speed marked

on the machine.

• Only use saw blades that match the speciﬁca-

tions given in this operating manual and that

have been tested and marked in accordance

with EN 847-1.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CS502AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info