Bedienungsanleitung Vonroc CT502DC (Seite 10 von 36) (Deutsch, Englisch, Holländisch, Französisch)

778552

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

WWW.VONROC.COM

- using the tool for different applications, or with

different or poorly maintainted accessories, may

signiﬁcantly increase the exposure level.

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the following text refer to the

pictures on page 2-4

1. Collet chuck

2. LED work light

3. Spindle lock

4A. Speed adjustment button “+”

4B. Speed adjustment button “-”

5. On/off button

6. Speed indication lights

7. Charger indication light

8. Chuck spanner

3. ASSEMBLY

Always make sure the machine is turned off

before mounting an accessory.

Warning! Change accessories by inserting

an accessory into the collet (or chuck) as far

possible to minimize run out and unbalance.

Assembly of accessories (Fig. B)

Press down the spindle lock (3) and hold it down.

Using the chuck spanner (8) you can undo the collet

chuck (1). Put the accessory in its place. Hold down

the spindle lock when you fasten the collet chuck

with the chuck spanner.

Do not press the spindle lock button while

the motor is running.

4. OPERATION

Switch on the machine by pressing the on/off

button (5).

With the speed adjustment button “+”(4A) or “-“(4B)

you can regulate the speed of the Combitool. Do not

put the machine down when the motor is still run-

ning. Do not place the machine on a dusty surface.

Dust particles may enter the mechanism.

Too high a load at a low speed of the

Combitool can burn out the engine.

The battery must be charged before ﬁrst use.

Charging the device (with the charger)

• Plug the charger plug into an electrical outlet

and wait for a while. The charger indication light

(7) will lighten up and show the charging status.

LED Charger status

Red Battery charging in progress

Green

Battery charging ﬁnished, battery fully charged

• After the battery is fully charged remove the

charger plug from the outlet and remove the

small plug from the device.

Holding and guiding the tool (Fig. C)

• For precision work (engraving): pencil grip (C1)

• For rough work (grinding): paring knife hand grip

(C2)

• When you need to keep the tool parallel to the

work surface (e.g. using a cut-off wheel): 2 hand

golf grip (C3)

Optimal use of the combi tool and its accessories

(Fig. A)

For optimal use of the accessories use the correct

speed. You can refer to the overview “Recommended

speed setting” below to determine the correct

speed, based on the material being worked on and

the type of accessory being used. This overview

enables you to select both correct accessory and

the optimum speed.

The 5 speeds indication lights (6) are equal to

the numbers 1, 2, 3, 4 and 5 in the overview

“Recommended speed setting”.

Ultimately, the best way to determine the correct

speed for work on any material is to practice on a

piece of scrap.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CT502DC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info