Bedienungsanleitung Vonroc CT503DC (Seite 9 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

764073

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

9WWW.VONROC.COM

tool and hold the power tool motionless until the

wheel comes to a complete stop. Never attempt

to remove the cut-off wheel from the cut while the

wheel is in motion otherwise kickback may occur.

Investigate and take corrective action to eliminate

the cause of wheel pinching or snagging.

Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted

in the workpiece.

Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The prot-

ruding wheel may cut gas or water pipes, electri-

cal wiring or objects that can cause kickback.

ADDITIONAL SAFETY INSTRUCTIONS FOR

WIRE BRUSHING OPERATIONS

Safety warnings speciﬁc for wire brushing operations:

a) Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive load

to the brush. The wire bristles can easily pene-

trate light clothing and/or skin.

b) Allow brushes to run at operating speed for at

least one minute before using them. During

this time no one is to stand in front or in line

with the brush. Loose bristles or wires will be

discharged during the run-in time.

c) Direct the discharge of the spinning wire brush

away from you. Small particles and tiny wire

fragments may be discharged at high velocity

during the use of these brushes and may beco-

me imbedded in your skin.

FOR THE CHARGER

Intended use

Charge only rechargeable battery packs. Other

types of batteries may burst causing personal

injury and damage.

The appliance is not to be used by persons (in-

cluding children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given super-

vision or instruction

b) Children being supervised not to play with the

appliance

c) Do not recharging non-rechargeable batteries!

d) During charging, batteries must be placed in the

well ventilated area!

Integrated batteries may only be removed for

disposal by qualiﬁed personnel. Opening the

housing shell can destroy the power tool.

To remove the battery from the power tool, press

the On/Off switch (5) until the battery is fully

discharged. Unscrew the screws on the housing

and remove the housing shell in order to remove

the battery. To prevent a short circuit, disconnect

the connectors on the battery one at a time and

then isolate the poles. Even when fully dischar-

ged, the battery still contains a residual capacity,

which can be released in case of a short circuit.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of ﬁre, electric shock and personal

injury. Read the following safety instructions.

Always check that the power supply

corresponds to the voltage on the rating plate.

Your machine is double insulated, therefore

no earthwire is required.

2. MACHINE INFORMATION

Intended use

This power tool is intended to function as a grinder,

sander, wire brush, polisher, carving or cut-off tool.

This combitool is great for editing of materials like

wood, plastic, stone, shell aluminium, brass and steel.

Always use the proper accessories and speed setting.

TECHNICAL SPECIFICATIONS

Model No. CT503DC

Rechargeable Battery 4V Li-ion 600mAh

Battery charging time 2 hours

Maximum disc diameter Ø35 mm

Maximum drill diameter Ø2.3 mm

No load speed 5000/10000/15000/min

Capacity of spring chuck 2.3 mm

Weight 0.1 kg

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CT503DC Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info