Bedienungsanleitung Vonroc GT502AC (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778575

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

WWW.VONROC.COM

5. Power cable

6. Upper housing

7. Lower housing

8. Protection guard

9. Spool assembly

10. Housing screw

11. Protection guard screw

12. Notch

13. Blade

14. Spool cover

15. Wire spool

16. Spring

17. Spool holder

3. ASSEMBLY

Cut injury when the unit starts accidentally.

Before you assemble the unit, make sure

that the mains cable is disconnected.

Assembling the housing (Fig. A, B, C)

1. Insert the lower housing (7) into the upper

housing (6), as shown on ﬁgure B. Ensure that

the cable is not stretched or caught when you

do this.

2. Secure both housing parts using the housing

screws (10), as shown on ﬁgure C. Use a screw

on both sides of the housing.

Mounting the protection guard (Fig. A, D)

1. Put the protection guard (8) onto the lower hou-

sing (7) by ﬁrst putting the guard into the notch

(12) and afterwards pulling the guard upwards.

2. Now secure the protection guard using the pro-

tection guard screw (11). A correctly assembled

protection guard is shown on ﬁgure D.

Replacing the wire spool (Fig. F1)

Before replacing the spool clean the

machine from any dirt.

• Remove the spool cover (14) by pressing the

two buttons on each side of the spool cover.

• Take out the spool reel (15) but leave the spring

(16) inside.

• Take the new spool reel (GT802AA) and place

it over the spring (16). Make sure the wires

are passed through the holes inside the spool

holder (17).

• Cover the new spool reel with the spool cover

(14) and make sure the buttons of the spool

cover (14) align properly with the holes inside

the spool holder (17).

4. OPERATION

Using the tap and go system (Fig. A, D)

To enable the tap and go system, the plastic cover

in front of the blade (13) in the protection guard (8)

must be removed.

Do not touch the blade (13) in the

protection guard (8) to prevent injury.

• When the wire is too short, switch the machine

on and press the tip of the spool reel (15) on

the ground (make sure this is done on a hard

surface).

• This will release the wire in order to get longer.

• The wire will be cut on the correct length

automatically by the blade (13) mounted in the

protection guard (8).

Using the cord grip (ﬁg. A, E)

To help secure the plug to the extension cord,

make a loop in the extension cord and attach it to

the cable hook as shown (see Fig. E). Once secure,

attach the cord to the plug. This will prevent acci-

dental ‘pull-out’.

Using the trimmer

Before use, always visually inspect the

machine and its parts are correctly

mounted, not worn out or damaged.

Hold the unit by the top part of the handle (1) and

the front handle (4) so that the trimmer head is

tilted a small distance forward. Make sure, the

ﬁlament does not touch hard objects such as walls,

stones and fences to prevent the ﬁlament from

welding together or breaking.

Switching On and Off (ﬁg. A)

• To switch the trimmer on, press the on/off

switch (2).

• To switch off, simply release the on/off switch

(2).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc GT502AC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info