Bedienungsanleitung Vonroc HA501AC (Seite 7 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

764012

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

WWW.VONROC.COM

DESCRIPTION

The numbers in the text refer to the diagrams on

pages 2 - 3

Fig. A-C

1. Switch

2. Ventilation slots

3. Nozzle outlet

4. Fishtail nozzle

5. Reduction nozzle

6. Glass protection nozzle

7. Flat rear side

3. OPERATION

The Hot air gun can be used for:

• Plumbing work like tube connections, solder,

bowing tubes;

• Removing paint, varnish and lacquer without

ﬁrerisk;

• Quickly drying of appliances which have beco-

me wet;

• Drying surfaces for quick repairing;

• Removing self-adhesive labels in a clean way

placing PVC labels;

• Blistering after sticking PVC materials can be

smoothed after heating;

• Easy removing of vinyl carpeting:

• Forming all synthetics with a low temperature

(400 degrees) among which polyethylene and

PVC;

•

Forming all synthetics with a high temperature

(600 degrees) among which acryl and plexiglass;

• Smelting synthetics, among which matters and

foils with PVC layer;

• Applying heat shrinking tubes;

• Shrinkwrappers;

• Thawing tubes and engines;

• Repairing ﬁnishing layers: enamel of bath and

household appliances; applying epoxypowder

coverlayers;

• Repairing of ski’s, surf-boards and other sports

goods;

•

Unscrewing too fast ﬁxed screws and connections.

Operation (Fig. A)

You can work manually with this hot air gun or you

can put it in a vertical position.

• Check if the mains switch is on position “0”

before you connect the apparatus;

• Keep the main lead always away from the hot

air stream and the mouth piece;

• Put the mains switch in position ‘I, II or III’ to let

your hot air gun operate:

"I" = 50 degrees, air ﬂow 500 l/min.

“II” = 400 degrees, air ﬂow 250 l/min.

“0” = Off

“III” = 600 degrees, air ﬂow 500 l/min.

When the temperature is excess 600° C, the heats

switches it off automatically, however, the heater

continues to run. When the heater has cooled to

operating temperature, the heater is switched on

again.

Switching off:

Slide the switch to 0.

Tip: If you want to get the best result, test all appli-

ances on a little part of the workpiece.

Flat rear side (Fig. C)

Inbetween usage, the machine can easily be placed

on its ﬂat rear side (7). This prevents any hot area

from the machine getting into contact with other

surfaces

The ﬂat rear side (7) also allows the machine to be

used in upright stationary mode.

After usage, always place the machine on its ﬂat

rear side (7). This allows the machine to cool down

safely.

Use of accessoires (Fig. B)

Fishtail nozzle (4)

Distributes air equally over ﬂat wide area.

Reduction nozzle (5)

Distributes air equally over small areas

Glass protection nozzle (6)

Deﬂects air away from glass for example when

stripping paint in window frames or softening putty.

4. MAINTENANCE

Always disconnect the apparatus before

carrying out inspection or cleaning. Never

use water or other liquids to clean the

electrical parts of the hot air gun.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc HA501AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vonroc HA501AC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info