Bedienungsanleitung Vonroc ID501AC (Seite 5 von 28) (Deutsch, Englisch, Holländisch, Französisch)

778543

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

WWW.VONROC.COM

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of ﬁre, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corre sponds to the voltage on the rating plate.

Class II machine - Double insulation -

You don’t need any earthed plug

If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk

of electric shock.

2. MACHINE INFORMATION

Intended use

Your impact drill has been designed for drilling

holes in wood, metal and plastics and for hammer

drilling in brick and concrete.

TECHNICAL SPECIFICATIONS

Model No. ID501AC

Mains voltage 230-240 V~

Mains frequency 50 Hz

Power input 500W

No-load speed 0-3.000/min

Impact rate 0-48.000/min

Chuck size 2-13 mm

Max. drill diameter Wood

Concrete

Steel

25 mm

10 mm

Weight 1.5 kg

Sound pressure level L

78 + 3 dB(A)

Sound power level L

89 + 3 dB(A)

Drilling into metal, a

h,D

2.93 + 1.5 m/s

Impact drilling into concrete,

h,ID

8.07 + 1.5 m/s

Vibration level

The vibration emission level stated in this instruction

manual has been measured in accordance with

a standardized test given in EN60745; it may be

used to compare one tool with another and as a

preliminary assessment of exposure to vibration

when using the tool for the applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories, may

signiﬁcantly increase the exposure level.

• The times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2.

Fig. A

1. Chuck

2. Function selection switch

3. Depth stop

4. Lock-on button

5. On/Off switch

6. Speed adjustment wheel

7. Left/right rotation switch

8. Side handle

9. Knob

Fig. B

10. Rear sleeve

11. Front sleeve

3. ASSEMBLY

Mounting and removing the auxiliary grip (Fig. A)

Mounting

• Loosen the auxiliary grip (9).

• Slide the auxiliary grip (8) over the chuck (1).

•

Turn the auxiliary grip (8) to the required position.

• Tighten the auxiliary grip (9).

Removing

• Loosen the auxiliary grip (9).

•

Remove the auxiliary grip (8) from the chuck (1).

• Tighten the auxiliary grip (9).

Exchanging and removing drill bits (Fig. A - B)

The machine is suitable for use of the following

drill bits:

• Wood (HSS)

• Metal (HSS)

• Concrete / masonry (hard metal)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc ID501AC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info