Bedienungsanleitung Vonroc JS501DC (Seite 8 von 28) (Deutsch, Englisch, Holländisch, Französisch)

764098

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

WWW.VONROC.COM

Switching the laser on/off (Fig. A)

• Press the laser switch (11) to switch the laser

on or off. The laser switch (11) also turns on the

LED worklight.

Adjusting the bevel angle (Fig. B, F)

1. Loosen the bolt (18), using the hex key (15).

2. Adjust the baseplate (9) to the desired position

(0°- 45°). The sawing angle (bevel) can be read

on the scale (7).

3. Tighten the bolt (7), using the hex key (15). It is

possible to store the hex key onto the machine,

as shown on Fig. B.

Adjusting the pendulum action (Fig. A)

The pendulum action switch is used to set the way

in which the teeth of the saw blade grip the material.

The pendulum action switch can be set to 4 positions:

0 - No pendulum action

1 - Small pendulum action

2 - Medium pendulum action

3 - Large pendulum action

The required pendulum action can be determined

by practical testing, although the following instruc-

tions can be observed:

• Soft material (wood, plastics etc.): set the pen-

dulum to level II or III. For a ﬁner and cleaner

saw cut, use pendulum level 0 or I.

• Thin material, use pendulum level 0.

• Hard material (steel etc.): set the pendulum to

level 0.

• Curves: set pendulum to level 0.

Plunge cutting (Fig. H)

Plunge cutting may only be used on soft materials

such as wood, aerated concrete, gypsum plaster

boards, etc. However, this requires a certain practi-

se and is only possible with short saw blades.

Place the saw onto the workpiece and switch it on.

Ensure that the bottom edge of the footplate rests

on the workpiece surface as shown on Fig. H.

3. Slowly saw into the workpiece at an angle, mo-

ving the saw to a vertical position and continue

to saw along the cutting line.

4. Switch the saw off and lift off the workpiece

when the work is complete.

Optimum use

• Clamp the workpiece. Use a clamping device for

small workpieces.

• Draw a line to deﬁne the direction in which to

guide the saw blade.

• Firmly hold the machine by the grip.

• Set the sawing speed.

• Set the mitre angle.

• Switch on the machine.

• Wait until the machine has reached full speed.

• Place the saw shoe on the workpiece.

• Slowly move the machine along the pre-drawn

line, ﬁrmly pressing the saw shoe against the

workpiece.

• Do not apply too much pressure on the machi-

ne. Let the machine do the work.

• Switch off the machine and wait for the ma-

chine to come to a complete standstill before

putting the machine down.

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

battery pack from the machine.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

move very persistent dirt using a soft cloth moiste-

ned with soapsuds. Do not use any solvents such

as gasoline, alcohol, ammonia, etc. Chemicals such

as these will damage the synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected at

the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic waste.

According to the European Guideline 2012/19/EC

for Waste Electrical and Electronic Equipment and its

implementation into national right, power tools that

are no longer usable must be collected separately

and disposed of in an environmentally friendly way.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc JS501DC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info