Bedienungsanleitung Vonroc JS502AC (Seite 7 von 28) (Deutsch, Englisch, Holländisch, Französisch)

764099

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

WWW.VONROC.COM

3. Speed adjustment wheel

4. Guard

5. Saw blade holder

6. Saw blade guide roller

7. Base plate

8. Hex key

9. Hex key holder

10. Dust extraction connection

11. Dust adapter

12. Grip

3. ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Mounting and removing the saw blade

Refer to the table below to select the required saw

blade.

Saw blade Material

Coarse Wood

Medium Wood

Fine Steel, aluminium, plastic

Very ﬁne Wood (curves)

Remove the guard from the machine to change the

saw blade.

Always saw with guard.

Fitting a saw blade (Fig. B)

The machine is equipped with a quick blade ex-

change system.

• Turn the clamping ring (13) of the saw blade

holder (5) completely to the left, in order to

open up the holder.

• Insert the saw blade (15) in the saw blade hol-

der (5) as far as possible. The teeth of the saw

blade (15) must point upward and forward. The

smooth side of the saw blade must engage in

the slot of the guide roller (6).

•

Release the clamping ring (13) to close the holder.

• Make sure when changing the saw blade that

the blade holder (5) is free of material debris

(such as splinters of wood or metal).

• Before use, always check that the saw blade is

securely ﬁxed.

Removing the saw blade

• Turn the clamping ring (13) of the saw blade

holder (5) completely to the left, in order to

open up the holder.

• Remove the saw blade from its holder.

• Release the clamping ring (13) to close the

holder.

4. OPERATION

Switching on and off (Fig. C)

• To switch on the machine, press the on/off

switch (1).

• To switch the machine to continuous mode,

keep the on/off switch (1) pressed and simulta-

neously press the lock-on button (2).

• To switch off continuous mode, press the on/

off switch (1) again.

• To switch off the machine, release the on/off

switch (1).

Setting the speed (Fig. C)

The speed adjustment wheel (3) is used for setting

the speed. The ideal speed depends on the proﬁle

and the teeth of the saw blade and on the material

to be worked.

Do not set the speed during use.

• Turn the speed adjustment wheel (3) to the

required position.

- For hard materials, use a saw blade with

ﬁne teeth and select a lower speed.

- For soft materials, use a saw blade with

coarse teeth and select a higher speed.

Setting the mitre angle (Fig. D)

The mitre angle is variable between 0° and 45°.

The mitre angle can be read from the scale.

Do not set the mitre angle during use.

• Slacken the Hex screws(14) using the Hex

key(8).

• Tilt the Base plate (7) to the required position.

• Tighten the Hex screws(14) using the Hex

key(8).

Dust extraction (Fig. E)

• Insert the dust extraction adapter (11) into the

dust extraction connection (10).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc JS502AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info