Bedienungsanleitung Vonroc JS503AC (Seite 7 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

764100

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

WWW.VONROC.COM

4. Auxiliary handle

5. Speed adjustment wheel

6. Pendulum action switch

7. Scale for bevel angle

8. Vacuum cleaner adapter

9. Baseplate

10. Guide roller

11. Clamping lever

12. Bolts for parallel guide

13. Hex key

14. Chuck

15. Saw blade

16. Bolt for baseplate

17. Parallel guide

18. Cutting mark

3. ASSEMBLY

Replacing the saw blade (Fig. A, B)

When mounting the saw blade, wear

protective gloves. Danger of injury when

touching the saw blade.

Only use saw blades that correspond with

the characteristic data given in the

operating instructions.

Mounting the saw blade

Make sure the blade holder is free of material

debris (such as splinters of wood or metal).

1. Turn the clamping lever (11) as far to the left as

possible and hold it in this position.

2. Insert the saw blade in the chuck (14). Check

that the saw blade is securely ﬁxed and that the

teeth are pointing in the cutting direction.

3. Let go of the clamping lever. Check whether the

back of the saw blade is positioned in the cent-

re of the guide roller (10). Make sure to use the

right sawblade for the corresponding material.

Included with the machine is a coarse sawblade

for wood and a ﬁne sawblade for metal and

plastics.

Removing the saw blade

1. Turn the clamping lever (11) as far to the left as

possible and hold it in this position.

2. Remove the saw blade from the chuck (14).

3. Let go of the clamping lever.

Attaching the parallel guide (Fig. C)

1. Loosen the bolts (12).

Mount the parallel guide (17) onto the baseplate

(9).

3. Set the desired cutting width using the scale

on the parallel guide (17) and the cutting mark

on the baseplate (9). The cutting mark (18)

indicates the position of the saw blade.

4. Tighten the bolts (12).

4. OPERATION

Switching on and off (Fig. A)

• To switch the machine on, push the switch

forward and press the On/off switch (1).

• To switch the machine off, release the On/off

switch (1).

Setting the speed (Fig. A)

The speed adjustment wheel (5) is used for setting

the speed. The ideal speed depends on the proﬁle

and the teeth of the saw blade and on the material

to be worked.

Do not set the speed during use.

• Turn the speed adjustment wheel (5) to the

required position.

- For hard materials, use a saw blade with

ﬁne teeth and select a lower speed.

- For soft materials, use a saw blade with

coarse teeth and select a higher speed.

Adjusting the bevel angle (Fig. A, D)

1. Loosen the bolts (16), using the hex key (13).

2. Adjust the baseplate (9) to the desired position

(0°- 45°). The sawing angle (bevel) can be read

on the scale (7).

3. Tighten the bolts (16), using the hex key (13). It

is possible to store the hex key onto the machi-

ne, as shown on Fig. A.

Adjusting the pendulum action (Fig. A)

The pendulum action switch (6) is used to set the

way in which the teeth of the saw blade grip the

material. The pendulum action switch can be set

to 4 positions:

0 - No pendulum action

1 - Small pendulum action

2 - Medium pendulum action

3 - Large pendulum action

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc JS503AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info