Bedienungsanleitung Vonroc MS501AC (Seite 12 von 92) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

764095

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

WWW.VONROC.COM

8. Length stop

9. Fence

10. Table extension

11. Table

12. Mounting holes

13. Kerf plate

14. Knob for mitre adjustment

15. Lever for mitre adjustment

16. Scale for mitre angle

17. Indicator for mitre angle

18. Laser

19. Indicator for bevel angle

20. Scale for bevel angle

21. Workpiece clamp

22. Knob for bevel adjustment

23. Roller

24. Depth adjustment bolt

25. Slide rails

26. Dust bag

27. Carrying handle

28. Dust outlet

29. Locking bolt for slide rails

30. Rear tilt protector

31. Stop bolt for 45° bevel angle

32. Stop bolt for 0° bevel angle

33. Locking bolt for workpiece clamp

34. Locking bolt for table extension

35. Locking bolt for adjustable fence

36. Adjustment bolt for fence

37. Front tilt protector

38. Position lock knob

39. Grub screw

40. Retaining bolt

41. Clamping ﬂange

42. Clamping bolt

43. Spindle lock

44. Knob for workpiece clamp

45. Knurled nut for depth adjustment

46. LED Worklight

47. Laser cover screws

48. Screws for laser adjustment

49. Lock nut for 45° bevel angle

50. Lock nut for 0° bevel angle

51. Fence bolts

3. ASSEMBLY

Before carrying out any work on the

machine, disconnect the mains plug from

the power supply.

Transport position (Fig. B, C)

The position lock knob (38) makes it easier to move

the power tool when transporting it to various

working locations.

Unlocking the transport position (work position)

1. Press the handle (2) downwards slightly;

2. Pull the position lock knob (38) fully outwards

and lock it in place by turning it;

3. Slowly move the handle (2) upwards.

Locking the transport position (transport position)

Before locking in transport position, make sure

that the depth adjustment bolt (24) is adjusted to

unlimited depth. This way, the handle (2) can be

moved fully downwards without touching the depth

stop. Also, remove all accessories that cannot be

securely ﬁtted to the machine.

1. Loosen the locking bolt for slide rails (29) if

tightened;

2. Pull the handle (2) forwards towards yourself

and tighten the locking bolt for slide rails (29);

3. Press the handle (2) fully downwards;

4. Lock the position lock knob (38) by ﬁrst pulling

and then turning it;

5. Wind up the mains cable and tie it together with

the supplied cable strap.

After locking the transport position, use the carrying

handle (27) to safely carry and transport the machine.

Only use the carrying handle to transport the

machine and never the protective guards.

Install of a stationary machine (Fig. A, B, D)

To ensure safe handling, the power tool must be

mounted on a ﬂat, stable work surface (e.g. work

bench) before use. You can install the machine in

three ways:

1. On a workbench

In this case the machine must be secured to the

workbench using suitable screw fasteners. Use the

four holes (12) to do this. As shown on ﬁg. D.

2. On a subframe

Read all the warnings and instructions

included with the saw stand. Failure to

observe the warnings and follow instructi-

ons may result in electric shock, ﬁre and/or

serious injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc MS501AC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info