Bedienungsanleitung Vonroc MS504AC (Seite 10 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

778562

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WWW.VONROC.COM

6) Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the

power tool is maintained.

SPECIFIC SAFETY INSTRUCTIONS

• Mitre saws are intended to cut wood or wood-li-

ke products, they cannot be used with abrasive

cut-off wheels for cutting ferrous material such

as bars, rods, studs, etc. Abrasive dust causes

moving parts such as the lower guard to jam.

Sparks from abrasive cutting will burn the lower

guard, the kerf insert and other plastic parts.

• Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand,

you must always keep your hand at least 100 mm

from either side of the saw blade. Do not use this

saw to cut pieces that are too small to be secure-

ly clamped or held by hand. If your hand is placed

too close to the saw blade, there is an increased

risk of injury from blade contact.

• The workpiece must be stationary and clamped

or held against both the fence and the table.

Do not feed the workpiece into the blade or cut

“freehand” in any way. Unrestrained or moving

workpieces could be thrown at high speeds,

causing injury.

• Push the saw through the workpiece. Do not

pull the saw through the workpiece. To make a

cut, raise the saw head and pull it out over the

workpiece without cutting, start the motor, press

the saw head down and push the saw through

the workpiece. Cutting on the pull stroke is likely

to cause the saw blade to climb on top of the

workpiece and violently throw the blade assem-

bly towards the operator.

• Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e.

holding the workpiece to the right of the saw

blade with your left hand or vice versa is very

dangerous.

• Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity

of the spinning saw blade to your hand may not

be obvious and you may be seriously injured.

• Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always

make certain that there is no gap between the

workpiece, fence and table along the line of the

cut. Bent or warped workpieces can twist or

shift and may cause binding on the spinning saw

blade while cutting. There should be no nails or

foreign objects in the workpiece.

• Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the workpie-

ce. Small debris or loose pieces of wood or other

objects that contact the revolving blade can be

thrown with high speed.

• Cut only one workpiece at a time. Stacked multi-

ple workpieces cannot be adequately clamped or

braced and may bind on the blade or shift during

cutting.

• Ensure the mitre saw is mounted or placed on a

level, ﬁrm work surface before use. A level and

ﬁrm work surface reduces the risk of the mitre

saw becoming unstable.

• Plan your work. Every time you change the bevel

or mitre angle setting, make sure the adjustable

fence is set correctly to support the workpie-

ce and will not interfere with the blade or the

guarding system. Without turning the tool “ON”

and with no workpiece on the table, move the

saw blade through a complete simulated cut to

assure there will be no interference or danger of

cutting the fence.

• Provide adequate support such as table exten-

sions, saw horses, etc. for a workpiece that is

wider or longer than the table top. Workpieces

longer or wider than the mitre saw table can tip

if not securely supported. If the cut-off piece or

workpiece tips, it can lift the lower guard or be

thrown by the spinning blade.

• Do not use another person as a substitute for

a table extension or as additional support. Un-

stable support for the workpiece can cause the

blade to bind or the workpiece to shift during the

cutting operation pulling you and the helper into

the spinning blade.

• The cut-off piece must not be jammed or pressed

by any means against the spinning saw blade. If

conﬁned, i.e. using length stops, the cut-off piece

could get wedged against the blade and thrown

violently.

• Always use a clamp or a ﬁxture designed to

properly support round material such as rods or

tubing. Rods have a tendency to roll while being

cut, causing the blade to “bite” and pull the work

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc MS504AC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info