Bedienungsanleitung Vonroc MS805AA (Seite 7 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

778564

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

WWW.VONROC.COM

1. Press the mounting bar lever (14) and hook the

opposite end of the mounting bar (7) onto the

frame (9) of the stand, as shown on ﬁgure C.

Lower the mounting bars (7) onto the frame and

release them to lock the mounting bar into place.

3. Repeat the same procedure with the other

mounting bar.

Attaching A Mitre Saw (Fig. D, E)

During operation and before starting a new

job, ensure that all screws and nuts are

tightened correctly and securely.

1. Adjust the mounting bars (7) to roughly the

width of the mitre saw base.

2. Place the mitre saw on the mounting bars (7)

and line up the holes in the mitre saw base with

the slots on the mounting bars (7).

3. Feed a bolt through the bottom of the mounting

bar (7) then through the base of the mitre saw.

4. Slide a washer and then a spring washer onto

the bolt and fasten it with a nut.

5. Repeat steps 3 and 4 for the other four holes on

the mitre saw base.

Attaching other types of machines that do not ﬁt

the standard mounting bars

Do not mount a table saw on this miter saw

stand. Aggressive feeding of sheet

materials into the table saw could cause

the stand to tip over.

To mount different machine types (that do not ﬁt

onto the mitre saw mounting bars), VONROC offers

MS807AA universal machine supports. To mount

these universal machine supports:

1. Connect the universal machine supports to the

mounting bars (7) and secure them with 4 hex-

agonal screws, 4 washers, 4 spring washers and

4 hexagonal nuts as supplied with the MS807AA

universal machine supports.

2. Place your tabletop machine onto the universal

machine supports.

3. Fasten the tabletop machine with 4 hexagonal

screws, 4 washers, 4 spring washers and 4 hex-

agonal nuts as supplied with the Mitre saw stand.

4. Tighten the screws after assembly.

5. Fasten the mounting bars (7) with the mounted

tabletop machine on the mitre saw stand, as

described in ‘Attaching A Mitre Saw’

Visit www.vonroc.com or contact Vonroc customer

service to acquire the MS807AA universal machine

supports.

4. OPERATION

Do not use the mitre saw stand until it is

completely assembled and you have read

and understood this entire manual and the

manual of the tool being used with this

mitre saw stand.

Do not use the mitre saw stand for

scaffolding or as a ladder. Make sure to

securely tighten all fasteners before use.

Maximum capacity is 150kg. Power tools

on the mitre saw stand should not exceed a

combined overall height of 150cm from the

ﬂoor.

Adjusting The Extension Arms (Fig. B, F)

1. Turn the extension arm knob (6) on the frame

counter-clockwise to loosen it.

2. Pull the extension arm (4) out to the desired

length. Note: The maximum extension length

is indicated on the extension arm (4). Do not

extend further than the maximum length.

3. Turn the extension arm knob (6) clockwise to

tighten it and secure the extension arm into

place.

Adjusting The Roller Height (Fig. F, G)

1. Turn the workpiece support knob (3) on the col-

lar of the extension arm (4) counter-clockwise

to loosen it.

2. Raise or lower the roller (1) to the desired

height.

3. Turn the workpiece support knob (3) clockwise

to tighten it and secure the roller (1) into place.

Using The end stop (Fig. B, F)

The mitre saw stand features end stops (5) which

allow repetitive cuts to be made quickly and accu-

rately.

1. Adjust the height of the workpiece support (2)

so that the lip of the end stop (5) is in line with

the work surface of the mitre saw.

2. Adjust the extension arms (4) to the desired

cutting length.

3. Place the end of the workpiece against the end

stop (5) and commence the cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc MS805AA Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info