Bedienungsanleitung Vonroc OS501AC (Seite 7 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

764082

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

WWW.VONROC.COM

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2.

1. On/off switch

2. Main grip

3. Dust box

4. Sanding pad

5. Sanding paper clamp

6. Auxiliary grip

7. Speed adjustment wheel

8. Sanding paper

3. ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Connecting the dust box (Fig. B)

It is highly recommended to use the machine with

the dust box (3), ensuring optimal dust collection.

• Slide the slot in the dust box over the notch on

the rear dust outlet.

•

To ensure the dust box is inserted securely, push

the dust box until a click-noise can be heard.

Note: The dust box should be emptied when the

box is half full to maintain optimal dust collection.

Mounting and removing sanding paper (Fig. C, D)

The sander is suitable for sanding paper both with

and without hook and loop fastening system.

Mounting and removing sanding paper with hook

and loop fastening

• Hold the machine on its side or upside down,

as shown on Fig. C

• Mount sanding paper (8) with the required

grain size onto the sanding pad (4). Make sure

that the perforation in the sanding paper (8)

corresponds with the perforation on the san-

ding pad (4).

• To remove the sanding paper (8), simply pull

the sanding paper from the sanding pad (4).

Mounting and removing sanding paper without

hook and loop fastening

• Open the sanding paper clamps (5).

• Mount sanding paper (8) with the required

grain size onto the sanding pad (4).

• Fold the sanding paper (8) at both ends around

the edges of the sanding pad (4).

• Close the sanding paper clamps (5) one by one.

Make sure that the ends of the sanding paper

(8) are clamped.

• To remove the sanding paper (8), ﬁrst open

the sanding paper clamps (5) and afterwards

remove the sanding paper (8) from the sanding

pad (4).

Note: Use coarse sanding paper for sanding rough,

uneven surfaces. Use medium sanding paper for

removing the remaining scratches from the coarse

sanding paper. Use ﬁne sanding paper for ﬁnishing

surfaces.

4. OPERATION

Switching on and off (Fig. A)

• To switch on the machine, press the on/off

switch (1) into position I.

• To switch off the machine, press the on/off

switch (1) into position 0.

Setting the speed (Fig. A)

The speed adjustment wheel is used for setting

the speed. The speed adjustment wheel can be set

to 7 positions. The ideal speed depends on the re-

quired grain size and on the material to be worked.

Do not set the speed during use.

Hints for optimum use

• Firmly hold the machine with both hands.

• Switch on the machine.

• Place the sanding pad with sanding paper on

the workpiece.

• Slowly move the machine over the workpiece,

ﬁrmly pressing the sanding pad against the

workpiece.

• Do not apply too much pressure on the machi-

ne. Let the machine do the work.

5. MAINTENANCE

Always disconnect the machine from the

main power supply before carrying out any

maintenance work.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc OS501AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info