Bedienungsanleitung Vonroc OT501DC (Seite 6 von 28) (Deutsch, Englisch, Holländisch, Französisch)

764071

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

WWW.VONROC.COM

with a standardised test given in EN 60745; it may

be used to compare one tool with another and as

a preliminary assessment of exposure to vibration

when using the tool for the applications mentioned:

- using the tool for different applications, or with

different or poorly maintainted accessories,

may signiﬁcantly increase the exposure level

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2.

1. On/off switch

2. Speed adjustment wheel

3. Mounting point for accessories

4. Grip

5. Quick change lever

6. Work light

7. Battery (not included)

8. Battery unlock button

3. ASSEMBLY

Before any work on the power tool, remove

the battery.

The battery must be charged before ﬁrst use.

Inserting the battery into the machine (Fig. C)

Ensure that the exterior of the battery is

clean and dry before connecting to the

charger or machine.

Insert the battery (7) into the base of the machine

as shown in Fig. C.

2. Push the battery further forward until it clicks

into place.

Removing the battery from the machine (Fig. C)

1. Push the battery unlock button (8).

2. Pull the battery out of the machine like shown

in Fig. C.

Removing and mounting accessories (ﬁg. B)

Worn or damaged accessories must be

replaced immediately.

Only use sharp and undamaged accessories.

•

Release the quick change lever (5) and slide the

accessory forward to remove from the holder.

• Slide the accessory in the holder and fasten the

quick change lever (5).

The sanding pad and the sanding paper must be

used for sanding applications.

4. OPERATION

Switching on and off (ﬁg. A)

• To switch on the machine, slide the on/off

switch (1) to the front.

• To switch off the machine, slide the on/off

switch (1) to the rear.

Setting the speed (ﬁg. A)

The speed adjustment wheel is used for setting the

speed. The speed adjustment wheel can be set to 6

positions. The ideal speed depends on the applica-

tion and on the material to be worked.

Do not set the speed during use.

• Turn the speed adjustment wheel (2) to the

required position.

Hints for optimum use

• Clamp the workpiece. Use a clamping device for

small workpieces.

• Draw a line to deﬁne the direction in which to

guide the accessory.

• Firmly hold the machine by the grip.

• Switch on the machine.

• Wait until the machine has reached full speed.

• Place the accessory on the workpiece.

• Slowly move the machine along the pre-drawn

line, ﬁrmly pressing the accessory against the

workpiece.

• Do not apply too much pressure on the machine.

Let the machine do the work.

• Switch off the machine and wait for the machine

to come to a complete standstill before putting

the machine down.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc OT501DC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info