Bedienungsanleitung Vonroc PM502AC (Seite 6 von 28) (Deutsch, Englisch, Holländisch, Französisch)

764131

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

WWW.VONROC.COM

Replacing the whisk (Fig. A)

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Use only whisks conform the speciﬁed diameter.

Always use a whisk that is suitable for the material

to be mixed/stirred. Using an unsuitable mixer bar

can unnecessarily overload both the machine and

yourself.

Mounting the whisk

1. Screw the assembled whisk into the tool holder

(5) in clockwise direction as far as possible.

2. Tighten the whisk into the tool holder using

the supplied spanners. To do so, hold the tool

holder (5) using one of the supplied spanners,

and use the second spanner to tighten the

assembled whisk.

Removing the whisk

1. Loosen the assembled whisk using the supplied

spanners. To do so, hold the tool holder (5)

using one of the supplied spanners, and use the

second spanner to loosen the assembled whisk.

2. Unscrew the whisk from the tool holder (5) in

anti-clockwise direction.

4. OPERATION

Switching on and off (Fig. A)

• To switch on the tool, press and hold the on/off

switch (1).

• If you release the on/off switch, the tool will be

switched off.

You can lock the on/off switch by pressing the

on/off switch (1) and then button (3). The switch

lock can be released by brieﬂy pressing the on/off

switch.

Gear selection (Fig. B)

Two mechanical speed ranges can be selected with

the gear selector switch (4):

Gear 1 180-400/min

Gear 2 300-700/min

The necessary gear depends on the type of the

material mixed and it is recommended to verify it

by a practical test.

Speed adjustment (Fig. B)

The required speed can be adjusted by using the

Speed adjustment wheel (3). Also during operation

the rotational speed can be adjusted.

•

To increase the speed, turn the Speed adjustment

knob (3) clockwise.

• To decrease the speed, turn the Speed adjustment

knob (3) anti-clockwise.

The required speeds depends on the material

and can be determined by practical testing.

Optimum use

•

For materials with low viscosity, e.g. emulsion

paint, varnishes, adhesive, grouting compound

and cement slurry, a stirrer whisk with a so-called

left-hand spiral is recommended for optimum

use. With a left-hand spiral, the material is moved

from the top downwards and the stirrer whisk is

pushed upwards. Materials with low viscosity are

mixed in a way which minimises splattering, so a

low speed is recommended (gear 1).

•

For materials with high viscosity, e.g. plaster,

concrete, cement, screed, ﬁller and epoxy resin, a

stirrer whisk with a so-called right-hand spiral is

recommended for optimum use. With a right-hand

spiral, the material is moved from the bottom

upwards and the stirrer whisk is pulled downwards

(working its way into the mixture). Materials with

high viscosity are mixed thoroughly, so a high

speed is recommended (gear 2).

• For optimum results, move the power tool in an

up and down motion while mixing.

• It is recommended to clean the whisk after use,

for example by stirring the whisk in a bucket

ﬁlled with water.

5. MAINTENANCE

Always disconnect the machine from the

main power supply before carrying out any

maintenance work.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt.

Remove very persistent dirt using a soft cloth

moistened with soapsuds. Do not use any solvents

such as gasoline, alcohol, ammonia, etc. Chemicals

such as these will damage the synthetic components.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc PM502AC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info