Bedienungsanleitung Vonroc PM508DC (Seite 7 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

819205

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

WWW.VONROC.COM

accessory could snag your clothing, pulling the

accessory into your body.

n) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the hou-

sing and excessive accumulation of powdered

metal may cause electrical hazards.

o) Do not operate the power tool near ﬂammable

materials. Sparks could ignite these materials.

p) Do not use accessories that require liquid cool-

ants. Using water or other liquid coolants may

result in electrocution or shock.

q) Do not allow any loose portion of the polishing

bonnet or its attachment strings to spin freely.

Tuck away or trim any loose attachment strings.

Loose and spinning attachment strings can

entangle your ﬁngers or snag on the workpiece.

r) Do not press the spindle lock until the tool stops.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or any

other accessory. Pinching or snagging causes rapid

stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite of the accessory’s rotation at

the point of the binding. For example, if an abrasive

wheel is snagged or pinched by the workpiece, the

edge of the wheel that is entering into the pinch

point can dig into the surface of the material cau-

sing the wheel to climb out or kick out. The wheel

may either jump toward or away from the operator,

depending on direction of the wheel’s movement

at the point of pinching. Abrasive wheels may also

break under these conditions. Kickback is the

result of power tool misuse and/or incorrect opera-

ting procedures or conditions and can be avoided

by taking proper precautions as given below.

a) Maintain a ﬁrm grip on the power tool and po-

sition your body and arm to allow you to resist

kickback forces. Always use auxiliary handle,

if provided, for maximum control over kickback

or torque reaction during start-up. The operator

can control torque reactions or kickback forces,

if proper precautions are taken.

b) Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

c) Do not position your body in the area where po-

wer tool will move if kickback occurs. Kickback

will propel the tool in direction opposite to the

wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent

kickback and loss of control.

SAFETY WARNINGS FOR BATTERY

a) Do not open the battery. Danger of shortcircui-

ting.

b) Protect the battery against heat, e. g., against

continuous intense sunlight, ﬁre, water, and

moisture. Danger of explosion.

c) In case of damage and improper use of the bat-

tery, vapours may be emitted. Ventilate the area

and seek medical help in case of complaints.

The vapours can irritate the respiratory system.

d) Use the battery only in conjunction with your

Vonroc product. This measure alone protects

the battery against dangerous overload.

e) The battery can be damaged by pointed objects

such as nails or screwdrivers or by force

applied externally. An internal short circuit can

occur and the battery can burn, smoke, explode

or overheat.

SAFETY WARNINGS FOR CHARGER

Intended use

Charge only CD801AA and CD803AA type rechar-

geable Battery packs with the charger. Other types

of batteries may burst causing personal injury and

damage.

a) The appliance is not to be used by persons

(including children) with reduced physical, sen-

sory or mental capabilities, or lack of experien-

ce and knowledge, unless they have been given

supervision or instruction.

b) Children being supervised not to play with the

appliance.

c) Do not recharging non-rechargeable batteries!

d) During charging, batteries must be placed in

the well ventilated area!

Electrical safety

Always check that the voltage of the power

supply corresponds to the voltage on the

rating plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc PM508DC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info